- 您現在的位置：買賣IC網 > PDF目錄1994 > DS3105LN+ (Maxim Integrated Products)IC TIMING LINE CARD 64-LQFP PDF資料下載
參數資料
| 型號： | DS3105LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 51/124頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TIMING LINE CARD 64-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 160 |
| 類型： | 定時卡 IC，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum，電信 |
| 輸入： | CMOS，LVDS，LVPECL，TTL |
| 輸出： | CMOS，LVDS，LVPECL，TTL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 5:2 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 312.5MHz |
| 電源電壓： | 1.62 V ~ 1.98 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
DS3105
32
or free-run to locked mode, the phase difference between the new reference and the output is measured and fed
into the DPLL loop to absorb the input phase difference. After a PBO event, regardless of the input phase
difference, the output phase transient is less than or equal to 5ns.
Any time that PBO is enabled it can also be frozen at the current phase offset by setting MCR10:PBOFRZ = 1.
When PBO is frozen, the T0 DPLL ignores subsequent phase build-out events and maintains the current phase
offset between inputs and outputs.
Disabling PBO while the T0 DPLL is not in the free-run or holdover states (locking or locked) causes a phase
change on the output clocks while the DPLL switches to tracking the selected reference with zero degrees of phase
error. The rate of phase change on the output clocks depends on the DPLL bandwidth. Enabling PBO (which
includes unfreezing) while locking or locked also causes a PBO event.
7.7.7.2 PBO Phase Offset Adjustment
An uncertainty of up to 5ns is introduced each time a phase build-out event occurs. This uncertainty results in a
phase hit on the output. Over a large number of phase build-out events, the mean error should be zero. The
PBOFF register specifies a small fixed offset for each phase build-out event to skew the average error toward zero
and eliminate accumulation of phase shifts in one direction.
7.7.8 Input to Output (Manual) Phase Adjustment
When phase build-out is disabled (PBOEN = 0 in MCR10), the OFFSET registers can be used to adjust the phase
of the T0 DPLL output clocks with respect to the selected reference when locked. Output phase offset can be
adjusted over a
±200ns range in 6ps increments. This phase adjustment occurs in the feedback clock so that the
output clocks are adjusted to compensate. The rate of change is therefore a function of DPLL bandwidth. Simply
writing to the OFFSET registers with phase build-out disabled causes a change in the input to output phase, which
can be considered to be a delay adjustment. Changing the OFFSET adjustment while in free-run or holdover state
does not cause an output phase offset until it exits the state and enters one of the locking states.
7.7.9 Phase Recalibration
When a phase buildout occurs, either automatic or manual, the feedback frequency synthesizer does not get an
internal alignment signal to keep it aligned with the output dividers, and therefore the phase difference between
input and output can become incorrect. Setting the FSCR3:RECAL bit periodically causes a recalibration process
to be executed, which corrects any phase error that may have occurred.
During the recalibration process the device puts the DPLL into mini-holdover, internally ramps the phase offset to
zero, resets all clock dividers, ramps the phase offset to the value stored in the OFFSET registers, and switches
the DPLL out of mini-holdover. If the OFFSET registers are written during the recalibration process, the process
ramps the phase offset to the new offset value.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3106LN+ | IC TIMING LINE CARD 64-LQFP |
| DS3231MZ+ | IC RTC I2C 8SOIC |
| DS3231SN#T&R | IC RTC W/TCXO 16-SOIC |
| DS3232MZ+ | IC RTC W/SRAM I2C 8SOIC |
| DS3232SN#T&R | IC RTC W/TCXO 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3105LN+ | 功能描述:計時器和支持產品 Line Card Timing IC RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS3106 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Line Card Timing IC |
| DS3106A10SL3S(621) | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S(621) | 制造商:Amphenol Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。