參數資料
型號： DS2196LN
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PQFP100
封裝： LQFP-100
文件頁數： 85/160頁
文件大?。?/td> 559K
代理商： DS2196LN
DS2196
30 of 160
5
PARALLEL PORT
The DS2196 is controlled via either a non-–multiplexed (MUX = 0) or a multiplexed (MUX = 1) bus by
an external microcontroller or microprocessor. The DS2196 can operate with either Intel or Motorola bus
timing configurations. If the BTS pin is tied low, Intel timing will be selected; if tied high, Motorola
timing will be selected. All Motorola bus signals are listed in parenthesis (). See the timing diagrams in
the AC Electrical Characteristics in Section 22 for more details.
6
CONTROL, ID, AND TEST REGISTERS
Each framer in the DS2196 is configured via a set of eleven control registers. Typically, the control
registers are only accessed when the system is first powered up. Once the DS2196 has been initialized,
the control registers will only need to be accessed when there is a change in the system configuration.
There are two Receive Control Registers (RCR1 and RCR2), two Transmit Control Registers (TCR1 and
TCR2), and seven Common Control Registers (CCR1 to CCR7).
Each of the eleven registers are
described in this section. There is a device Identification Register (IDR) at address 0Fh. The MSB of this
read–only register is fixed to a 0 indicating that a T1 device is present. The next 3 MSBs are used to
indicate which T1 device is present. The lower 4 bits of the IDR are used to display the die revision of
the chip.
Power–Up Sequence
The DS2196 does not automatically clear its register space on power–up. After the supplies are stable,
the register space should be configured for operation by writing to all of the internal registers. This
includes setting the Test and all unused registers to 00Hex.
This can be accomplished using a two-pass approach.
1. Clear DS2196 register space by writing 00h to the addresses 00h through 0FFh.
2. Program required registers to achieve desired operating mode.
IDR: DEVICE IDENTIFICATION REGISTER (Address = 0F Hex)
(MSB)
(LSB)
0011
ID3
ID2
ID1
ID0
SYMBOL
POSITION
NAME AND DESCRIPTION
0IDR.7
Chip ID Bit 3. MSB of DS2196 identification code. Set to 0.
0IDR.6
Chip ID Bit 2. DS2196 identification code. Set to 0.
1IDR.5
Chip ID Bit 1. DS2196 identification code. Set to 1.
1IDR.4
Chip ID Bit 0. LSB of DS2196 identification code. Set to 1.
ID3
IDR.3
Chip Revision Bit 3. MSB of a decimal code that represents
the chip revision.
ID2
IDR.1
Chip Revision Bit 2.
ID1
IDR.2
Chip Revision Bit 1.
ID0
IDR.0
Chip Revision Bit 0. LSB of a decimal code that represents the
chip revision.
相關PDF資料
PDF描述
DS21FF44 DATACOM, FRAMER, PBGA300
DS21FF44N DATACOM, FRAMER, PBGA300
DS21FT40N DATACOM, FRAMER, PBGA300
DS21FT40 DATACOM, FRAMER, PBGA300
DS21FT42 DATACOM, FRAMER, PBGA300
相關代理商/技術參數
參數描述
DS2196LN+ 功能描述:網絡控制器與處理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS219T 功能描述:烙鐵 DESOLDERING HEAD RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
DS21E352 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E352N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E354 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*