參數資料
型號： DS2196LN
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PQFP100
封裝： LQFP-100
文件頁數： 134/160頁
文件大小： 559K
代理商： DS2196LN
DS2196
75 of 160
RDS0MA: RECEIVE DS0 MONITOR REGISTER FRAMER A
(Address = 1F Hex)
RDS0MB: RECEIVE DS0 MONITOR REGISTER FRAMER B
(Address = BF Hex)
(MSB)
(LSB)
B1
B2
B3
B4
B5
B6
B7
B8
SYMBOL
POSITION
NAME AND DESCRIPTION
B1
RDS0M.7
Receive DS0 Channel Bit 1. MSB of the DS0 channel (first bit
to be received).
B2
RDS0M.6
Receive DS0 Channel Bit 2.
B3
RDS0M.5
Receive DS0 Channel Bit 3.
B4
RDS0M.4
Receive DS0 Channel Bit 4.
B5
RDS0M.3
Receive DS0 Channel Bit 5.
B6
RDS0M.2
Receive DS0 Channel Bit 6.
B7
RDS0M.1
Receive DS0 Channel Bit 7.
B8
RDS0M.0
Receive DS0 Channel Bit 8. LSB of the DS0 channel (last bit
to be received).
11
PER–CHANNEL CODE (IDLE) GENERATION AND LOOPBACK
The DS2196 can replace data on a channel–by–channel basis in both the transmit and receive directions.
The transmit direction is from the backplane to the T1 line and is covered in Section 11.1. The receive
direction is from the T1 line to the backplane and is covered in Section 11.2.
11.1 TRANSMIT SIDE CODE GENERATION
The Transmit Idle Registers (TIR1/2/3) are used to determine which of the 24 T1 channels should be
overwritten with the code placed in the Transmit Idle Definition Register (TIDR). This method allows the
same 8–bit code to be placed into any of the 24 T1 channels. If this method is used, then the CCR4.0
control bit must be set to 0.
Each of the bit position in the Transmit Idle Registers (TIR1/TIR2/TIR3) represent a DS0 channel in the
outgoing frame. When these bits are set to a 1, the corresponding channel will transmit the Idle Code
contained in the Transmit Idle Definition Register (TIDR). Bit 7 stuffing will occur over the programmed
Idle Code unless the DS0 channel is made transparent by the Transmit Transparency Registers.
The Transmit Idle Registers (TIRs) have an alternate function that allows them to define a Per–Channel
Loopback (PCLB). If the TIRFS control bit (CCR4.0) is set to 1, then the TIRs will determine which
channels (if any) from the backplane should be replaced with the data from the receive side or in other
words, off of the T1 line. If this mode is enabled, then transmit and receive clocks and frame syncs must
be synchronized.
One method to accomplish this would be to tie RCLK to TCLK and RSYNC to
TSYNC.
相關PDF資料
PDF描述
DS21FF44 DATACOM, FRAMER, PBGA300
DS21FF44N DATACOM, FRAMER, PBGA300
DS21FT40N DATACOM, FRAMER, PBGA300
DS21FT40 DATACOM, FRAMER, PBGA300
DS21FT42 DATACOM, FRAMER, PBGA300
相關代理商/技術參數
參數描述
DS2196LN+ 功能描述:網絡控制器與處理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS219T 功能描述:烙鐵 DESOLDERING HEAD RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
DS21E352 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E352N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E354 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*