參數資料
型號： ADUC7126BSTZ126-RL
廠商： Analog Devices Inc
文件頁數： 93/108頁
文件大?。?/td> 0K
描述： IC MCU 16/32B 126KB FLASH 80LQFP
標準包裝： 1,000
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 41.78MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 40
程序存儲器容量： 126KB（63K x 16）
程序存儲器類型： 閃存
RAM 容量： 32K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 12x12b，D/A 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 80-LQFP
包裝： 帶卷 (TR)
Data Sheet
ADuC7124/ADuC7126
Rev. C | Page 85 of 108
IRQEN Register
IRQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled to
create an IRQ exception. When a bit is set to 0, the correspond-
ing source request is disabled or masked, which does not create
an IRQ exception. The IRQEN register cannot be used to
disable an interrupt.
IRQEN Register
Name:
IRQEN
Address:
0xFFFF0008
Default Value:
0x00000000
Access:
Read/write
IRQCLR Register
IRQCLR is a write-only register that allows the IRQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the IRQEN register without
affecting the remaining bits. The pair of registers, IRQEN and
IRQCLR, allow independent manipulation of the enable mask
without requiring an atomic read-modify-write.
This register should be used to disable an interrupt source only
during the following conditions:
In the interrupt sources interrupt service routine.
When the peripheral is temporarily disabled by its own
control register.
This register should not be used to disable an IRQ source if that
IRQ source has an interrupt pending or may have an interrupt
pending.
IRQCLR Register
Name:
IRQCLR
Address:
0xFFFF000C
Default Value:
0x00000000
Access:
Write only
FAST INTERRUPT REQUEST (FIQ)
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface and provides the
second level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Bit 31 to Bit 1 of FIQSTA are logically OR’ed to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and FIQCLR does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN clears, as a side effect, the same bit in IRQEN.
Likewise, a bit set to 1 in IRQEN clears, as a side effect, the
same bit in FIQEN. An interrupt source can be disabled in both
the IRQEN and FIQEN masks.
FIQSIG
FIQSIG reflects the status of the different FIQ sources. If a
peripheral generates an FIQ signal, the corresponding bit in
the FIQSIG is set; otherwise, it is cleared. The FIQSIG bits are
cleared when the interrupt in the particular peripheral is
cleared. All FIQ sources can be masked in the FIQEN MMR.
FIQSIG is read only.
FIQSIG Register
Name:
FIQSIG
Address:
0xFFFF0104
Default Value:
0x00000000
Access:
Read only
FIQEN
FIQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled to
create an FIQ exception. When a bit is set to 0, the correspond-
ing source request is disabled or masked, which does not create
an FIQ exception. The FIQEN register cannot be used to disable an
interrupt.
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default Value:
0x00000000
Access:
Read/write
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
This register should be used to disable an interrupt source only
during the following conditions:
In the interrupt sources interrupt service routine.
The peripheral is temporarily disabled by its own control
register.
This register should not be used to disable an IRQ source if that
IRQ source has an interrupt pending or may have an interrupt
pending.
相關PDF資料
PDF描述
ADUC7129BSTZ126 IC DAS MCU ARM7 ADC/DDS 80-LQFP
ADUC812BSZ-REEL IC MCU FLASH 12BIT ADC 52MQFP
ADUC814BRU IC ADC 12BIT W/FLASH MCU 28TSSOP
ADUC816BCP IC MCU 8K FLASH ADC/DAC 56LFCSP
ADUC824BSZ-REEL IC MCU 8K FLASH ADC/DAC 52MQFP
相關代理商/技術參數
參數描述
ADUC7128 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-bit ADC & DDS DAC
ADUC7128BCPZ126 功能描述:IC DAS MCU ARM7 ADC/DDS 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587
ADUC7128BCPZ1262 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
ADUC7128BCPZ126-RL 功能描述:IC DAS MCU ARM7 ADC/DDS 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7128BCPZ126-RL2 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*