參數資料
型號： ORT82G5
英文描述： ORCA ORT82G5 1.0.1-25/2.0-2.5/3.125 Gbits/s Backplane Interface FPSC
中文描述： ORCA的ORT82G5 1.0.1-25/2.0-2.5/3.125 Gb /秒背板接口促進文化基金
文件頁數： 58/92頁
文件大小： 1823K
代理商： ORT82G5
58
Agere Systems Inc.
Preliminary Data Sheet
July 2001
1.0-1.25/2.0-2.5/3.125 Gbits/s Backplane Interface
ORCA
ORT82G5 FPSC Eight-Channel
Pin Information
(continued)
Table 23. FPGA Common-Function Pin Description
(continued)
* The FPGA States of Operation section contains more information on how to control these signals during start-up. The timing of DONE release
is controlled by one set of bit stream options, and the timing of the simultaneous release of all other configuration pins (and the activation of all
user I/Os) is controlled by a second set of options.
Symbol
I/O
Description
Special-Purpose Pins
(Can also be used as a general I/O.)
M[3:0]
I
During powerup and initialization, M0
—
M3 are used to select the configuration mode with
their values latched on the rising edge of INIT. During configuration, a pull-up is enabled.
I/O After configuration, these pins are user-programmable I/O.*
PLL_CK[0:7]
I/O Dedicated PCM clock pins. These pins are user-programmable I/O pins if not used by PLLs.
P[TBTR]CLK[1:0][
TC]
pairing. They may be used as general I/O pins if not needed for clocking purposes.
TDI, TCK, TMS
I
If boundary scan is used, these pins are test data in, test clock, and test mode select inputs.
If boundary scan is not selected, all boundary scan functions are inhibited once configura-
tion is complete. Even if boundary scan is not used, either TCK or TMS must be held at
logic 1 during configuration. Each pin has a pull-up enabled during configuration.
I/O After configuration, these pins are user-programmable I/O.*
RDY/BUSY/RCLK
O
During configuration in peripheral mode, RDY/RCLK indicates another byte can be written
to the FPGA. If a read operation is done when the device is selected, the same status is
also available on D7 in asynchronous peripheral mode.
After configuration, if the MPI is not used, this pin is a user-programmable I/O pin.*
I/O During the master parallel configuration mode, RCLK is a read output signal to an external
memory. This output is not normally used.
HDC
O
High during configuration is output high until configuration is complete. It is used as a con-
trol output, indicating that configuration is not complete.
I/O After configuration, this pin is a user-programmable I/O pin.*
LDC
O
Low during configuration is output low until configuration is complete. It is used as a control
output, indicating that configuration is not complete.
I/O After configuration, this pin is a user-programmable I/O pin.*
INIT
I/O INIT is a bidirectional signal before and during configuration. During configuration, a pull-up
is enabled, but an external pull-up resistor is recommended. As an active-low, open-drain
output, INIT is held low during power stabilization and internal clearing of memory. As an
active-low input, INIT holds the FPGA in the wait-state before the start of configuration.
After configuration, this pin is a user-programmable I/O pin.*
CS0, CS1
I
CS0 and CS1 are used in the asynchronous peripheral, slave parallel, and microprocessor
configuration modes. The FPGA is selected when CS0 is low and CS1 is high. During con-
figuration, a pull-up is enabled.
I/O After configuration, these pins are user-programmable I/O pins.*
RD/MPI_STRB
I
RD is used in the asynchronous peripheral configuration mode. A low on RD changes D7
into a status output. As a status indication, a high indicates ready, and a low indicates busy.
WR and RD should not be used simultaneously. If they are, the write strobe overrides.
This pin is also used as the MPI data transfer strobe.
I/O After configuration, if the MPI is not used, this pin is a user-programmable I/O pin.*
I/O Pins dedicated for the primary clock. Input pins on the middle of each side with differential
相關PDF資料
PDF描述
ORT8850 Field-Programmable System Chip (FPSC) Eight-Channel x 850 Mbits/s Backplane Transceiver
ORT8850H Field-Programmable System Chip (FPSC) Eight-Channel x 850 Mbits/s Backplane Transceiver
ORT8850L Field-Programmable System Chip (FPSC) Eight-Channel x 850 Mbits/s Backplane Transceiver
OS1001 Interface IC
OS1010 Optoelectronic
相關代理商/技術參數
參數描述
ORT82G5-1BM680C 功能描述:FPGA - 現場可編程門陣列 10368 LUT 372 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORT82G5-1BM680I 功能描述:FPGA - 現場可編程門陣列 10368 LUT 372 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORT82G5-1F680C 功能描述:FPGA - 現場可編程門陣列 ORCA FPSC 3.7GBITS/s BP XCVR 643K RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORT82G5-1F680I 功能描述:FPGA - 現場可編程門陣列 ORCA FPSC 2.7Gbits/s BP XCVR 643K RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
ORT82G5-1FN680C 功能描述:FPGA - 現場可編程門陣列 ORCA FPSC 1.5V 3.7 G b Bpln Xcvr 643K Gt RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*