- 您現在的位置：買賣IC網 > PDF目錄231501 > W972GG8JB-25 (WINBOND ELECTRONICS CORP) 256M X 8 DDR DRAM, 0.4 ns, PBGA60 PDF資料下載
參數資料
| 型號： | W972GG8JB-25 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | DRAM |
| 英文描述： | 256M X 8 DDR DRAM, 0.4 ns, PBGA60 |
| 封裝： | 11 X 11.50 MM, ROHS COMPLIANT, WBGA-60 |
| 文件頁數： | 21/86頁 |
| 文件大小： | 1466K |
| 代理商： | W972GG8JB-25 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
W972GG8JB
Publication Release Date: Feb. 18, 2011
- 28 -
Revision A02
active bank will begin to precharge on the rising edge which is CAS Latency (CL) clock cycles before
the end of the read burst.
Auto-precharge is also implemented during Write commands. The precharge operation engaged by
the Auto-precharge command will not begin until the last data of the burst write sequence is properly
stored in the memory array.
This feature allows the precharge operation to be partially or completely hidden during burst read
cycles (dependent upon CAS Latency) thus improving system performance for random data access.
The RAS lockout circuit internally delays the Precharge operation until the array restore operation
has been completed (tRAS satisfied) so that the Auto-precharge command may be issued with any
read or write command.
7.7.1
Burst read with Auto-precharge
If A10 is HIGH when a Read Command is issued, the Read with Auto-precharge function is engaged.
The DDR2 SDRAM starts an Auto-precharge operation on the rising edge which is (AL + BL/2) cycles
later from the Read with AP command if tRAS(min) and tRTP(min) are satisfied. (Example timing
waveform refer to 10.23 Burst read operation with Auto-precharge diagram in Chapter 10)
If tRAS(min) is not satisfied at the edge, the start point of Auto-precharge operation will be delayed until
tRAS(min) is satisfied.
If tRTP(min) is not satisfied at the edge, the start point of Auto-precharge operation will be delayed until
tRTP(min) is satisfied.
In case the internal precharge is pushed out by tRTP, tRP starts at the point where tRTP ends (not at the
next rising clock edge after this event). So for BL = 4 the minimum time from Read with Auto-
precharge to the next Activate command becomes AL + RU{ (tRTP + tRP) / tCK } (Example timing
waveform refer to 10.24 Burst read operation with Auto-precharge diagram in Chapter 10.), for BL = 8
the time from Read with Auto-precharge to the next Activate command is AL + 2 + RU{ (tRTP + tRP) /
tCK
}, where RU stands for “rounded up to the next integer”. In any event internal precharge does not
start earlier than two clocks after the last 4-bit prefetch.
A new bank active command may be issued to the same bank if the following two conditions are
satisfied simultaneously.
The
RAS precharge time (tRP) has been satisfied from the clock at which the Auto-precharge
begins.
The RAS cycle time (tRC) from the previous bank activation has been satisfied.
(Example timing waveforms refer to 10.25 to 10.26 Burst read with Auto-precharge followed by an
activation to the same bank (tRC Limit) and (tRP Limit) diagram in Chapter 10)
7.7.2
Burst write with Auto-precharge
If A10 is HIGH when a Write Command is issued, the Write with Auto-Precharge function is engaged.
The DDR2 SDRAM automatically begins precharge operation after the completion of the burst write
plus write recovery time (WR) programmed in the mode register. The bank undergoing Auto-
precharge from the completion of the write burst may be reactivated if the following two conditions are
satisfied.
The data-in to bank activate delay time (WR + tRP) has been satisfied.
The
RAS cycle time (tRC) from the previous bank activation has been satisfied.
(Example timing waveforms refer to 10.27 to 10.28 Burst write with Auto-precharge (tRC Limit) and
(WR + tRP Limit) diagram in Chapter 10)
相關PDF資料 |
PDF描述 |
|---|---|
| WF512K32-150CJC | 512K X 32 FLASH 5V PROM MODULE, 150 ns, CQCC68 |
| W73B586A-09L | 32K X 18 CACHE SRAM, 9 ns, PQCC52 |
| WS512K32-100G4TM | 2M X 8 MULTI DEVICE SRAM MODULE, 100 ns, CQFP68 |
| WS512K32-35G4M | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68 |
| WS512K32-35G4Q | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W972GG8JB-25I | 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 80WBGA |
| W972GG8JB-3 | 制造商:Winbond Electronics Corp 功能描述:DRAM Chip DDR2 SDRAM 2G-Bit 256Mx8 1.8V 60-Pin WBGA 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 3NS |
| W9751G6IB-25 | 功能描述:IC DDR2-800 SDRAM 512MB 84-WBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| W9751G6JB | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M ? 4 BANKS ? 16 BIT DDR2 SDRAM |
| W9751G6JB-25 | 制造商:Winbond Electronics Corp 功能描述:512GB DDRII |
發布緊急采購，3分鐘左右您將得到回復。