- 您現在的位置：買賣IC網 > PDF目錄231501 > W972GG8JB-25 (WINBOND ELECTRONICS CORP) 256M X 8 DDR DRAM, 0.4 ns, PBGA60 PDF資料下載
參數資料
| 型號： | W972GG8JB-25 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | DRAM |
| 英文描述： | 256M X 8 DDR DRAM, 0.4 ns, PBGA60 |
| 封裝： | 11 X 11.50 MM, ROHS COMPLIANT, WBGA-60 |
| 文件頁數： | 2/86頁 |
| 文件大?。?/td> | 1466K |
| 代理商： | W972GG8JB-25 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
W972GG8JB
Publication Release Date: Feb. 18, 2011
- 10 -
Revision A02
Notes:
1. To guarantee ODT off, VREF must be valid and a LOW level must be applied to the ODT pin.
2. VREF must be within
300 mV with respect to VDDQ/2 during supply ramp time.
3. VDD/VDDL voltage ramp time must be no greater than 200 mS from when VDD ramps from 300 mV to VDD min.
4. The VDDQ voltage ramp time from when VDD min is achieved on VDD to when VDDQ min is achieved on VDDQ must be
no greater than 500 mS.
tCH tCL
tIS
400nS
NOP
PRE
ALL
EMRS
MRS
PRE
ALL
REF
MRS
REF
EMRS
ANY
CMD
tRP
tMRD
tRP
tRFC
tOIT
Follow OCD
Flow chart
OCD
CAL. Mode
Exit
OCD
Default
min 200 Cycle
DLL
Reset
DLL
Enable
CLK
CKE
Command
ODT
tMRD
Figure 1
– Initialization sequence after power-up
7.2
Mode Register and Extended Mode Registers Operation
For application flexibility, burst length, burst type, CAS Latency, DLL reset function, write recovery
time (WR) are user defined variables and must be programmed with a Mode Register Set (MRS)
command. Additionally, DLL disable function, driver impedance, additive CAS Latency, ODT (On Die
Termination), single-ended strobe and OCD (off chip driver impedance adjustment) are also user
defined variables and must be programmed with an Extended Mode Register Set (EMRS) command.
Contents of the Mode Register (MR) or Extended Mode Registers EMR (1), EMR (2) and EMR (3) can
be altered by re-executing the MRS or EMRS Commands. Even if the user chooses to modify only a
subset of the MR or EMR (1), EMR (2) and EMR (3) variables, all variables within the addressed
register must be redefined when the MRS or EMRS commands are issued.
MRS, EMRS and Reset DLL do not affect array contents, which mean re-initialization including those
can be executed at any time after power-up without affecting array contents.
7.2.1
Mode Register Set Command (MRS)
(
CS = "L", RAS = "L", CAS = "L",
WE = "L", BA0 = "L", BA1 = "L", BA2 = "L", A0 to A14 =
Register Data)
The mode register stores the data for controlling the various operating modes of DDR2 SDRAM. It
programs CAS Latency, burst length, burst sequence, test mode, DLL reset, Write Recovery (WR) and
various vendor specific options to make DDR2 SDRAM useful for various applications. The default
value in the Mode Register after power-up is not defined, therefore the Mode Register must be
programmed during initialization for proper operation.
The DDR2 SDRAM should be in all bank precharge state with CKE already HIGH prior to writing into
the mode register. The mode register set command cycle time (tMRD) is required to complete the write
operation to the mode register. The mode register contents can be changed using the same command
and clock cycle requirements during normal operation as long as all banks are in the precharge state.
The mode register is divided into various fields depending on functionality. Burst length is defined by
相關PDF資料 |
PDF描述 |
|---|---|
| WF512K32-150CJC | 512K X 32 FLASH 5V PROM MODULE, 150 ns, CQCC68 |
| W73B586A-09L | 32K X 18 CACHE SRAM, 9 ns, PQCC52 |
| WS512K32-100G4TM | 2M X 8 MULTI DEVICE SRAM MODULE, 100 ns, CQFP68 |
| WS512K32-35G4M | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68 |
| WS512K32-35G4Q | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W972GG8JB-25I | 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 2.5NS 80WBGA |
| W972GG8JB-3 | 制造商:Winbond Electronics Corp 功能描述:DRAM Chip DDR2 SDRAM 2G-Bit 256Mx8 1.8V 60-Pin WBGA 制造商:Winbond Electronics Corp 功能描述:IC DDR2 SDRAM 2GBIT 3NS |
| W9751G6IB-25 | 功能描述:IC DDR2-800 SDRAM 512MB 84-WBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| W9751G6JB | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M ? 4 BANKS ? 16 BIT DDR2 SDRAM |
| W9751G6JB-25 | 制造商:Winbond Electronics Corp 功能描述:512GB DDRII |
發布緊急采購，3分鐘左右您將得到回復。