- 您現在的位置：買賣IC網 > PDF目錄379803 > CD1865 (Intel Corp.) Intelligent Eight-Channel Communications Controller PDF資料下載
參數資料
| 型號： | CD1865 |
| 廠商： | Intel Corp. |
| 英文描述： | Intelligent Eight-Channel Communications Controller |
| 中文描述： | 智能八通道通信控制器 |
| 文件頁數： | 80/150頁 |
| 文件大?。?/td> | 871K |
| 代理商： | CD1865 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁
CD1865
—
Intelligent Eight-Channel Communications Controller
80
Datasheet
When the CD1865 is programmed to detect level changes and generate service requests when level
changes occur, it does so in firmware by reading the pins and comparing to a previously stored
value. This function is performed in the main timing loop of the firmware; the maximum time
required to detect a level change under worst-case conditions is approximately 2 ms. When the
CD1865 is performing this function, the modem pins are periodically sampled rather than
continuously monitored; as such they have very little sensitivity to noise, which is desirable in data
communication applications. However, in extremely noisy applications, re-read a modem line
which has caused a Modem Signal Change Service Request to verify that it has indeed changed and
is not merely malfunctioning. This eliminates even the slight possibility of a noise pulse causing
erratic operation.
When the CD1865 is monitoring modem pins to control transmit or receive functions, it does not
rely on the previously stored value, but checks the pins at the appropriate time. Thus, there is very
little delay in this response. For example, before deciding to transmit another character, it examines
the CTS* pin at that time. (The CD1865 makes this decision when moving characters from the
FIFO to the Holding register, not from the Holding register to the Shift register.) Refer to
Section 7.3 on page 72
for flow-control details.
Note that the logical sense of the modem bits is inverted; for example, writing a
‘
1
’
to the MSVR
causes the output pin to go to nominal zero volts. Likewise, a low-voltage input is sensed as a
‘
1
’
.
7.4.1
Generating Service Requests with Modem Pins
The CD1865 can generate service requests when any one of the input pins changes state. Either or
both edges may be detected by setting bits in the two Modem Change Option registers (MCOR1
and MCOR2). For each pin, the user can individually enable on-to-off or off-to-on transition
detection of the inputs. When the CD1865 detects such a transition, it sets the corresponding bit in
the Modem Change register. If the corresponding bit in the channel
’
s set, the CD1865 asserts its *
output. The user must clear the Modem Change register during the service request service routine
before writing to the .
The CD1865 performs this task by reading the modem input signals and comparing the current
value with the value read in the last pass through the outer scanning loop. Because this is the
lowest-priority event in the CD1865 scanning loop, changes may not be detected unless they are
several hundred microseconds long. Modem Input pins can be used for purposes such as detecting
the closing of a switch. However, the relatively slow speed of response should be taken into
account when using Modem Input pins for this purpose. The CD1865 does not latch the Modem
input signals.
7.4.2
Using Modem Pins as General-Purpose I/O
Since the modem pins can be directly accessed by the host, they can be used as general-purpose I/O
pins if they are not needed for flow control or modem interfacing. Simply read from and write to
them as any I/O port.
7.5
Testing the CD1865
—
Loopback Tests
The CD1865 performs a basic internal self-test whenever it is reset. This test provides a reasonable
degree of confidence that the CD1865 is functioning satisfactorily. There are two additional tests
that can be performed by the user to further ensure complete functionality. These two test modes
相關PDF資料 |
PDF描述 |
|---|---|
| CD22100 | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100E | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100F | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22101 | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
| CD22101E | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CD1865N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1865P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1867N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。