- 您現在的位置：買賣IC網 > PDF目錄379803 > CD1865 (Intel Corp.) Intelligent Eight-Channel Communications Controller PDF資料下載
參數資料
| 型號： | CD1865 |
| 廠商： | Intel Corp. |
| 英文描述： | Intelligent Eight-Channel Communications Controller |
| 中文描述： | 智能八通道通信控制器 |
| 文件頁數： | 68/150頁 |
| 文件大?。?/td> | 871K |
| 代理商： | CD1865 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁
CD1865
—
Intelligent Eight-Channel Communications Controller
68
Datasheet
7.1.10
Programming Notes
If a special condition (for example, framing or a parity error) occurred on a special character, the
CD1865 does not interpret this character as matched. Flow-control characters that are processed
and discarded because FCT is set never cause an overrun.
Special Character Recognition only occurs on characters that have no other problems or errors.
There is one case where the CD1865 does not find a special character even though the character
has been correctly received. If a good character arrives as the ninth character (for example, the
FIFO is full), it stays in a Holding register. If another character arrives, the good character in the
Holding register has its status marked as
‘
overflow
’
, indicating that it is the last good character
received; however, it is not recognized as a special character.
There are two cases where the CD1865 might not detect a two-character sequence. If the first
character has been found, but no other character has been received for a long period of time and the
Receive Time-out event occurs, no match is found because the first character is flushed up to the
host. If special-character detection is disabled by clearing SCDE just when the CD1865 has
received the first two-character special-character sequence, but has not received the second
character yet, the first character is lost.
7.2
Transmitter Operation
7.2.1
Basic Operation
Refer to
Figure 24 on page 69
for a diagram of transmitter operation. Upon power-on reset, all
transmitters are disabled with their Transmit Output held in the
‘
Mark
’
or a logic
‘
1
’
condition.
Other channel parameters are undefined. The minimum configuration of a channel for transmission
consists of specifying the bit rate, parity, and number of Stop bits. In-band and Out-of-Band Flow
Control should also be set as required. Next, set either (or both) of the service request enable bits.
Then issue the Transmit Enable Command and either of two service request enable bits. For normal
operation, set the TxRDY bit. This causes a service request to be issued when the FIFO is empty.
Since on power-up the FIFO is empty, a service request is received (less than 1 ms.), and at that
time data can be transferred to the FIFO. Data can not be transferred to the FIFO as part of channel
initialization; instead one has to be in the service-request routine to do this. Refer to the
Section 5.3
for details.
Once the channel is initialized and serviced, and a character is written into the Transmit FIFO, the
transmitter starts to transmit by first sending the Start bit (space or a logic
‘
0
’
) followed by the data
character according to predefined character length, least significant bit first. An optional parity bit
(none, odd, even, or forced) is appended followed by the final Stop bit (a logic
‘
1
’
or a
‘
Mark
’
).
The length of the Stop bit can be one, one-and-a-half, two, or two-and-a-half bit-times long.
The transmitter continues sending characters one after the other until the Transmit FIFO is empty.
When the Transmit FIFO is empty and the last character is sent, the transmitter stops transmission
and holds the TxD Output in the
‘
Mark
’
(1) condition. Transmission resumes another character is
in the FIFO.
In some cases it must be determined if the channel is completely done transmitting the last bit of
the last character
—
for instance, before changing the bit rate. In such a case, the service request is
to be issued only when the last character is sent, rather than when the FIFO is empty. In this case,
instead of setting the TxRDY bit, set the TxMpty bit. This causes a service request to be issued
only when the transmitter is completely empty.
相關PDF資料 |
PDF描述 |
|---|---|
| CD22100 | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100E | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22100F | CMOS 4 x 4 Crosspoint Switch with Control Memory High-Voltage Type (20V Rating) |
| CD22101 | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
| CD22101E | CMOS 4 x 4 x 2 Crosspoint Switch with Control Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CD1865N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1865P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1866P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| CD1867N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。