參數(shù)資料
型號: UPD703130GC-8EU
廠商: NEC Corp.
英文描述: MOS INTEGRATED CIRCUIT
中文描述: 馬鞍山集成電路
文件頁數(shù): 70/72頁
文件大?。?/td> 601K
代理商: UPD703130GC-8EU
Preliminary Data Sheet U15390EJ1V0DS
70
μ
PD703130
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note:
Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and
ultimately degrade the device operation. Steps must be taken to stop generation of static electricity
as much as possible, and quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using
insulators that easily build static electricity. Semiconductor devices must be stored and transported
in an anti-static container, static shielding bag or conductive material. All test and measurement
tools including work bench and floor should be grounded. The operator should be grounded using
wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need
to be taken for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note:
No connection for CMOS device inputs can be cause of malfunction. If no connection is provided
to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence
causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels
of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused
pin should be connected to V
DD
or GND with a resistor, if it is considered to have a possibility of
being an output pin. All handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note:
Power-on does not necessarily define initial status of MOS device. Production process of MOS
does not define the initial operation status of the device. Immediately after the power source is
turned ON, the devices with reset function have not yet been initialized. Hence, power-on does
not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the
reset signal is received. Reset operation must be executed immediately after power-on for devices
having reset function.
Reference materials
Electrical Characteristics for Microcomputer (U15170J
Note
)
Note
This document number is that of Japanese version.
The related documents indicated in this publication may include preliminary versions. However, preliminary
versions are not marked as such.
V850E/MS1, V850E/MS2, and V850 Family are trademarks of NEC Corporation.
相關PDF資料
PDF描述
UPD703130 MOS INTEGRATED CIRCUIT
UPD703201 32-BIT SINGLE-CHIP MICROCONTROLLERS
UPD703204 32-BIT SINGLE-CHIP MICROCONTROLLERS
UPD70F30025AGC-25 LJT 24C 12#16 12#12 PIN PLUG
UPD70F3004AGC-33 32-bit RISC Microcontrollers
相關代理商/技術參數(shù)
參數(shù)描述
UPD703131A 制造商:NEC 制造商全稱:NEC 功能描述:32-Bit Single-Chip Microcontrollers
UPD703131AF1-EN4 制造商:NEC 制造商全稱:NEC 功能描述:32-Bit Single-Chip Microcontrollers
UPD703131AF1-XXX-EN4 制造商:NEC 制造商全稱:NEC 功能描述:32-Bit Single-Chip Microcontrollers
UPD703131AGJ-XXX-UEN 制造商:NEC 制造商全稱:NEC 功能描述:32-Bit Single-Chip Microcontrollers
UPD703131AY 制造商:NEC 制造商全稱:NEC 功能描述:32-Bit Single-Chip Microcontrollers