- 您現在的位置：買賣IC網 > PDF目錄383838 > ST20GP6 MAX 7000 CPLD 256 MC 208-RQFP PDF資料下載
參數資料
| 型號： | ST20GP6 |
| 英文描述： | MAX 7000 CPLD 256 MC 208-RQFP |
| 中文描述： | GPS處理器 |
| 文件頁數： | 76/116頁 |
| 文件大?。?/td> | 1107K |
| 代理商： | ST20GP6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
ST20-GP1
76/116
For 1.5 stop bits, the majority decision of the fifteenth, sixteenth, and seventeenth samples during
the stop bits is used to determine the effective stop bit value.
When the last stop bit has been received (at the end of the last programmed stop bit period) the
content of the receive shift register is transferred to the receive data buffer register
(
ASCRxBuffer
). The receive buffer full flag (
RxBufFull
) is set, and the parity (
ParityError
) and
framing error (
FrameError
) flags are updated, after the last stop bit has been received (at the end
of the last stop bit programmed period), regardless of whether valid stop bits have been received or
not. The receive circuit then waits for the next start bit (falling edge transition) at the
RXD
pin.
Reception is stopped by clearing the
RxEnable
bit. A currently received frame is completed
including the generation of the receive status flags. Start bits that follow this frame will not be
recognized.
Note
: In wake-up mode, received frames are only transferred to the receive buffer register if the ninth
bit (the wake-up bit) is 1. If this bit is 0, the receive buffer full (
RxBufFull
) flag will not be set and no
data will be transferred.
13.2 Hardware error detection capabilities
To improve the safety of serial data exchange, the ASC provides three error status flags in the
ASCStatus
register which indicate if an error has been detected during reception of the last data
frame and associated stop bits.
The parity error (
ParityError
) bit is set when the parity check on the received data is incorrect.
The framing error (
FrameError
) bit is set when the
RXD
pin is not a 1 during the programmed
number of stop bit times, sampled as described in the section above.
The overrun error (
OverrunError
) bit is set when the last character received in the
ASCRxBuffer
register has not been read out before reception of a new frame is complete.
These flags are updated simultaneously with the transfer of data to the receive buffer.
13.3 Baud rate generation
The ASC has its own dedicated 16-bit baud rate generator with 16-bit reload capability.
The baud rate generator is clocked with the CPU clock. The timer counts downwards and can be
started or stopped by the
Run
bit in the
ASCControl
register. Each underflow of the timer provides
one clock pulse. The timer is reloaded with the value stored in its 16-bit reload register each time it
underflows. The
ASCBaudRate
register is the dual-function baud rate generator/reload register. A
read from this register returns the content of the timer, writing to it updates the reload register.
An auto-reload of the timer with the content of the reload register is performed each time the
ASCBaudRate
register is written to. However, if the
Run
bit is 0 at the time the write operation to
the
ASCBaudRate
register is performed, the timer will not be reloaded until the first CPU clock
cycle after the
Run
bit is 1.
相關PDF資料 |
PDF描述 |
|---|---|
| ST25C02AB1 | IC FLEX 6000 FPGA 16K 144-TQFP |
| ST25C02AB6 | Stratix FPGA 25K FBGA-672 |
| ST25C02AM1 | IC ACEX 1K FPGA 100K 208-PQFP |
| ST25C02AM6 | Cyclone II FPGA 20K FBGA-256 |
| ST25C04ML1 | IC FLEX 6000 FPGA 24K 144-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST20-GP6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CT33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CX33S | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6CX33STR | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6X33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。