- 您現在的位置：買賣IC網 > PDF目錄383838 > ST20GP6 MAX 7000 CPLD 256 MC 208-RQFP PDF資料下載
參數資料
| 型號： | ST20GP6 |
| 英文描述： | MAX 7000 CPLD 256 MC 208-RQFP |
| 中文描述： | GPS處理器 |
| 文件頁數： | 68/116頁 |
| 文件大?。?/td> | 1107K |
| 代理商： | ST20GP6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
ST20-GP1
68/116
upsetting the error status of any complex operation being carried out by the pre-empted low priority
process.
In the event of a processor halting because of
HaltOnError
, the link will finish outstanding transfers
before shutting down. If
CPUAnalyse
is asserted then all inputs continue but outputs will not make
another access to memory for data. Memory refresh will continue to take place.
11.2 Bootstrap
The ST20-GP1 can be bootstrapped from external ROM, internal ROM or from a link. This is
determined by the setting of the
BootSource0-1
pins, see Table 9.1 on page 52. If both
BootSource0-1
pins are held low it will boot from a link. If either or both pins are held high, it will
boot from ROM. This is sampled once only by the ST20-GP1, before the first instruction is
executed after reset.
11.2.1 Booting from ROM
When booting from ROM, the ST20-GP1 starts to execute code from the top two bytes in external
memory, at address #7FFFFFFE which should contain a backward jump to a program in ROM.
11.2.2 Booting from link
When booting from a link, the ST20-GP1 will wait for the first bootstrap message to arrive on the
link. The first byte received down the link is the control byte. If the control byte is greater than 1 (i.e.
2 to 255), it is taken as the length in bytes of the boot code to be loaded down the link. The bytes
following the control byte are then placed in internal memory starting at location
MemStart
.
Following reception of the last byte the ST20-GP1 will start executing code at
MemStart
. The
memory space immediately above the loaded code is used as work space. A byte arriving on the
bootstrapping link after the last bootstrap byte, is retained and no acknowledge is sent until a
process inputs from the link.
11.2.3 Peek and poke
Any location in internal or external memory can be interrogated and altered when the ST20-GP1 is
waiting for a bootstrap from link.
When booting from link, if the first byte (the control byte) received down the link is greater than 1, it
is taken as the length in bytes of the boot code to be loaded down the link.
If the control byte is 0 then eight more bytes are expected on the link. The first four byte word is
taken as an internal or external memory address at which to poke(write) the second four byte
word.
If the control byte is 1 the next four bytes are used as the address from which to peek(read) a word
of data; the word is sent down the output channel of the link.
相關PDF資料 |
PDF描述 |
|---|---|
| ST25C02AB1 | IC FLEX 6000 FPGA 16K 144-TQFP |
| ST25C02AB6 | Stratix FPGA 25K FBGA-672 |
| ST25C02AM1 | IC ACEX 1K FPGA 100K 208-PQFP |
| ST25C02AM6 | Cyclone II FPGA 20K FBGA-256 |
| ST25C04ML1 | IC FLEX 6000 FPGA 24K 144-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST20-GP6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CT33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CX33S | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6CX33STR | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6X33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。