- 您現在的位置：買賣IC網 > PDF目錄383838 > ST20GP6 MAX 7000 CPLD 256 MC 208-RQFP PDF資料下載
參數資料
| 型號： | ST20GP6 |
| 英文描述： | MAX 7000 CPLD 256 MC 208-RQFP |
| 中文描述： | GPS處理器 |
| 文件頁數： | 30/116頁 |
| 文件大?。?/td> | 1107K |
| 代理商： | ST20GP6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
ST20-GP1
30/116
workspace. The values of
Iptr
and
Status
to be used by the interrupt handler are loaded from this
workspace and starts executing the handler. The value of
Wptr
is then set to the bottom of this
save area.
When an interrupt occurs when the CPU was idle or running at low priority, the
Status
is saved.
This indicates that no valid process is running (Null Status). The interrupted processes (low priority
process) state is stored in shadow registers. This state can be accessed via the ldshadow (load
shadow registers) and stshadow (store shadow registers) instructions. The interrupt handler is then
run at high priority.
When the interrupt routine has completed it must adjust
Wptr
to the value at the start of the handler
code and then execute the iret (interrupt return) instruction. This restores the interrupted state from
the interrupt handler structure and signals to the interrupt controller that the interrupt has
completed. The processor will then continue from where it was before being interrupted.
5.3
Interrupt latency
The interrupt latency is dependent on the data being accessed and the position of the interrupt
handler and the interrupted process. This allows systems to be designed with the best trade-off use
of fast internal memory and interrupt latency.
5.4
Pre-emption and interrupt priority
Each interrupt channel has an implied priority fixed by its place in the interrupt vector table. All
interrupts will cause scheduled processes of any priority to be suspended and the interrupt handler
started. Once an interrupt has been sent from the controller to the CPU the controller keeps a
record of the current executing interrupt priority. This is only cleared when the interrupt handler
executes a return from interrupt (iret) instruction. Interrupts of a lower priority arriving will be
blocked by the interrupt controller until the interrupt priority has descended to such a level that the
routine will execute. An interrupt of a higher priority than the currently executing handler will be
passed to the CPU and cause the current handler to be suspended until the higher priority interrupt
is serviced.
In this way interrupts can be nested and a higher priority interrupt will always pre-empt a lower
priority one. Deep nesting and placing frequent interrupts at high priority can result in a system
where low priority interrupts are never serviced or the controller and CPU time are consumed in
nesting interrupt priorities and not executing the interrupt handlers.
5.5
Restrictions on interrupt handlers
There are various restrictions that must be placed on interrupt handlers to ensure that they interact
correctly with the rest of the process model implemented in the CPU.
1
Interrupt handlers must not deschedule.
2
Interrupt handlers must not execute communication instructions. However they may com-
municate with other processes through shared variables using the semaphore signal to
synchronize.
3
Interrupt handlers must not perform block move instructions.
4
Interrupt handlers must not cause program traps. However they may be trapped by a
scheduler trap.
相關PDF資料 |
PDF描述 |
|---|---|
| ST25C02AB1 | IC FLEX 6000 FPGA 16K 144-TQFP |
| ST25C02AB6 | Stratix FPGA 25K FBGA-672 |
| ST25C02AM1 | IC ACEX 1K FPGA 100K 208-PQFP |
| ST25C02AM6 | Cyclone II FPGA 20K FBGA-256 |
| ST25C04ML1 | IC FLEX 6000 FPGA 24K 144-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST20-GP6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CT33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
| ST20GP6CX33S | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6CX33STR | 功能描述:射頻無線雜項 GPS Processor RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| ST20GP6X33S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:GPS PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。