參數資料
型號: MB9AF312MPMC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封裝: 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數: 96/114頁
文件大?。?/td> 1357K
代理商: MB9AF312MPMC
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
82
15.2.1 Definitions
Many register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter
number, in this case 0. A lower case “x” replaces the output compare Unit, in this case compare unit A or compare unit B.
However, when using the register or bit defines in a program, the precise form must be used, i.e., TCNT0 for accessing
Timer/Counter0 counter value and so on.
The definitions in Table 15-1 are also used extensively throughout the document.
15.2.2 Registers
The Timer/Counter (TCNT0) and output compare registers (OCR0A and OCR0B) are 8-bit registers. Interrupt request
(abbreviated to Int.Req. in the figure) signals are all visible in the timer interrupt flag register (TIFR0). All interrupts are
individually masked with the timer interrupt mask register (TIMSK0). TIFR0 and TIMSK0 are not shown in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T0 pin. The clock select
logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The
Timer/Counter is inactive when no clock source is selected. The output from the clock select logic is referred to as the timer
clock (clkT0).
The double buffered output compare registers (OCR0A and OCR0B) are compared with the Timer/Counter value at all
times. The result of the compare can be used by the waveform generator to generate a PWM or variable frequency output on
the output compare pins (OC0A and OC0B). See Section 16.7.3 “Using the Output Compare Unit” on page 107 for details.
The compare match event will also set the compare flag (OCF0A or OCF0B) which can be used to generate an output
compare interrupt request.
15.3
Timer/Counter Clock Sources
The Timer/Counter can be clocked by an internal or an external clock source. The clock source is selected by the clock
select logic which is controlled by the clock select (CS02:0) bits located in the Timer/Counter control register (TCCR0B). For
Table 15-1. Definitions
Parameter
Definition
BOTTOM
The counter reaches the BOTTOM when it becomes 0x00.
MAX
The counter reaches its MAXimum when it becomes 0xFF (decimal 255).
TOP
The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The
TOP value can be assigned to be the fixed value 0xFF (MAX) or the value stored in the OCR0A register.
The assignment is dependent on the mode of operation.
相關PDF資料
PDF描述
MB9AF312LPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
MB9AF311NPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100
MB9AF316NPMC RISC MICROCONTROLLER, PQFP100
MB9AF314NPMC RISC MICROCONTROLLER, PQFP100
MB9AF312NPF RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB9AF314LAPMC1-G-JNE2 制造商:FUJITSU 功能描述:
MB9AF314LAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF314LAQN-G-AVE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 64-QFN Exposed Pad (9x9) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包裝:托盤 零件狀態:有效 核心處理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 連接性:CSIO,I2C,LIN,UART/USART,USB 外設:DMA,LVD,POR,PWM,WDT I/O 數:51 程序存儲容量:256KB(256K x 8) 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:32K x 8 電壓 - 電源(Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 9x12b 振蕩器類型:內部 工作溫度:-40°C ~ 105°C(TA) 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN 裸露焊盤(9x9) 標準包裝:260
MB9AF314LPMC1-ESE1 制造商:FUJITSU 功能描述:
MB9AF314LPMC1-GE1 制造商:FUJITSU 功能描述: