參數資料
型號： MB9AF312MPMC
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封裝： 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數： 18/114頁
文件大?。?/td> 1357K
代理商： MB9AF312MPMC
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
114
The Timer/Counter overflow flag (TOV1) is set at the same timer clock cycle as the OCR1x registers are updated with the
double buffer value (at BOTTOM). When either OCR1A or ICR1 is used for defining the TOP value, the OC1A or ICF1 flag
set when TCNT1 has reached TOP. The interrupt flags can then be used to generate an interrupt each time the counter
reaches the TOP or BOTTOM value.
When changing the TOP value the program must ensure that the new TOP value is higher or equal to the value of all of the
compare registers. If the TOP value is lower than any of the compare registers, a compare match will never occur between
the TCNT1 and the OCR1x.
As Figure 16-9 shows the output generated is, in contrast to the phase correct mode, symmetrical in all periods. Since the
OCR1x registers are updated at BOTTOM, the length of the rising and the falling slopes will always be equal. This gives
symmetrical output pulses and is therefore frequency correct.
Using the ICR1 register for defining TOP works well when using fixed TOP values. By using ICR1, the OCR1A register is
free to be used for generating a PWM output on OC1A. However, if the base PWM frequency is actively changed by
changing the TOP value, using the OCR1A as TOP is clearly a better choice due to its double buffer feature.
In phase and frequency correct PWM mode, the compare units allow generation of PWM waveforms on the OC1x pins.
Setting the COM1x1:0 bits to two will produce a non-inverted PWM and an inverted PWM output can be generated by setting
the COM1x1:0 to three (See Table on page 117). The actual OC1x value will only be visible on the port pin if the data
direction for the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the OC1x
register at the compare match between OCR1x and TCNT1 when the counter increments, and clearing (or setting) the OC1x
register at compare match between OCR1x and TCNT1 when the counter decrements. The PWM frequency for the output
when using phase and frequency correct PWM can be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x register represents special cases when generating a PWM waveform output in the phase
correct PWM mode. If the OCR1x is set equal to BOTTOM the output will be continuously low and if set equal to TOP the
output will be set to high for non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. If
OCR1A is used to define the TOP value (WGM13:0 = 9) and COM1A1:0 = 1, the OC1A output will toggle with a 50% duty
cycle.
16.10 Timer/Counter Timing Diagrams
The Timer/Counter is a synchronous design and the timer clock (clkT1) is therefore shown as a clock enable signal in the
following figures. The figures include information on when interrupt flags are set, and when the OCR1x register is updated
with the OCR1x buffer value (only for modes utilizing double buffering). Figure 16-10 shows a timing diagram for the setting
of OCF1x.
Figure 16-10.Timer/Counter Timing Diagram, Setting of OCF1x, no Prescaling
fOCnxPFCPWM
fclk_I/O
2N
×
TOP
×
-------------------------------
=
OCRnx - 1
clkI/O
(clkI/O/1)
TCNTn
OCRnx
OCFnx
clkTn
OCRnx
OCRnx Value
OCRnx + 1
OCRnx + 2
相關PDF資料
PDF描述
MB9AF312LPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
MB9AF311NPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100
MB9AF316NPMC RISC MICROCONTROLLER, PQFP100
MB9AF314NPMC RISC MICROCONTROLLER, PQFP100
MB9AF312NPF RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB9AF314LAPMC1-G-JNE2 制造商:FUJITSU 功能描述:
MB9AF314LAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF314LAQN-G-AVE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 64-QFN Exposed Pad (9x9) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包裝:托盤 零件狀態:有效 核心處理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 連接性:CSIO，I2C，LIN，UART/USART，USB 外設:DMA，LVD，POR，PWM，WDT I/O 數:51 程序存儲容量:256KB（256K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:32K x 8 電壓 - 電源（Vcc/Vdd）:2.7 V ~ 5.5 V 數據轉換器:A/D 9x12b 振蕩器類型:內部 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN 裸露焊盤（9x9） 標準包裝:260
MB9AF314LPMC1-ESE1 制造商:FUJITSU 功能描述:
MB9AF314LPMC1-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*