參數資料
型號： MB9AF312MPMC
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封裝： 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數： 70/114頁
文件大?。?/td> 1357K
代理商： MB9AF312MPMC
59
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
13.
External Interrupts
The external interrupts are triggered by the INT0 and INT1 pins or any of the PCINT23...0 pins. Observe that, if enabled, the
interrupts will trigger even if the INT0 and INT1 or PCINT23...0 pins are configured as outputs. This feature provides a way of
generating a software interrupt. The pin change interrupt PCI2 will trigger if any enabled PCINT[23:16] pin toggles. The pin
change interrupt PCI1 will trigger if any enabled PCINT[14:8] pin toggles. The pin change interrupt PCI0 will trigger if any
enabled PCINT[7:0] pin toggles. The PCMSK2, PCMSK1 and PCMSK0 registers control which pins contribute to the pin
change interrupts. Pin change interrupts on PCINT23...0 are detected asynchronously. This implies that these interrupts can
be used for waking the part also from sleep modes other than idle mode.
The INT0 and INT1 interrupts can be triggered by a falling or rising edge or a low level. This is set up as indicated in the
specification for the external interrupt control register A – EICRA. When the INT0 or INT1 interrupts are enabled and are
configured as level triggered, the interrupts will trigger as long as the pin is held low. Note that recognition of falling or rising
edge interrupts on INT0 or INT1 requires the presence of an I/O clock, described in
Section 9.1 “Clock Systems and their Distribution” on page 24. Low level interrupt on INT0 and INT1 is detected
asynchronously. This implies that this interrupt can be used for waking the part also from sleep modes other than Idle mode.
The I/O clock is halted in all sleep modes except Idle mode.
Note:
Note that if a level triggered interrupt is used for wake-up from power-down, the required level must be held
long enough for the MCU to complete the wake-up to trigger the level interrupt. If the level disappears before
the end of the start-up time, the MCU will still wake up, but no interrupt will be generated. The start-up time is
defined by the SUT and CKSEL fuses as described in
13.1
Pin Change Interrupt Timing
An example of timing of a pin change interrupt is shown in Figure 13-1.
Figure 13-1. Timing of Pin Change Interrupts
clk
pin_lat
pin_sync
PCINT(0)
pcint_in_(0)
pcint_syn
pcint_setflag
PCIF
pin_lat
pin_sync
pcint_sync
clk
x
0
clk
pcint_setflag
PCINT(0) in PCMSK(x)
PCINT(0)
PCIF
pcint_in_(0)
DQ
LE
DQ
相關PDF資料
PDF描述
MB9AF312LPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP64
MB9AF311NPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP100
MB9AF316NPMC RISC MICROCONTROLLER, PQFP100
MB9AF314NPMC RISC MICROCONTROLLER, PQFP100
MB9AF312NPF RISC MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
MB9AF314LAPMC1-G-JNE2 制造商:FUJITSU 功能描述:
MB9AF314LAPMC-G-JNE2 制造商:Fujitsu 功能描述:Bulk
MB9AF314LAQN-G-AVE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310A Microcontroller IC 32-Bit 40MHz 256KB (256K x 8) FLASH 64-QFN Exposed Pad (9x9) 制造商:cypress semiconductor corp 系列:FM3 MB9A310A 包裝:托盤 零件狀態:有效 核心處理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 連接性:CSIO，I2C，LIN，UART/USART，USB 外設:DMA，LVD，POR，PWM，WDT I/O 數:51 程序存儲容量:256KB（256K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:32K x 8 電壓 - 電源（Vcc/Vdd）:2.7 V ~ 5.5 V 數據轉換器:A/D 9x12b 振蕩器類型:內部 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:64-VFQFN 裸露焊盤 供應商器件封裝:64-QFN 裸露焊盤（9x9） 標準包裝:260
MB9AF314LPMC1-ESE1 制造商:FUJITSU 功能描述:
MB9AF314LPMC1-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*