參數資料
型號： ST7285C
廠商： 意法半導體
英文描述： 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
中文描述： 8位微控制器48,000鐵路發展策略光盤，3K內存，ADC，兩個定時器，2個SPI，I2C和脊髓損傷接口
文件頁數： 53/117頁
文件大小： 748K
代理商： ST7285C
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
53/117
ST7285C
SERIAL PERIPHERAL INTERFACE
(Cont’d)
4.4.9Serial Peripheral Data I/O Register (SPDR)
Address: see Memory Map
Reset Value: XXh
—
Read/Write
The Serial Peripheral Data I/O Register is used to
transmit and receive data on the serial bus. Only a
write to this register will initiate transmission/re-
ception of another byte and this will only occur in
the Master device. A Slave device writing to its
data I/O register will not initiate a transmission. Af-
ter having transmitted a byte of data, the SPIF sta-
tus bit is set in both the Master and Slave devices.
A write or read of the Serial Peripheral Data I/O
Register, after accessing the Serial Peripheral
Status Register with SPIF set, will clear SPIF.
During the clock cycle the SPIF bit is being set, a
copy of the received data byte in the shift register
is being moved to a buffer. When the user reads
the Serial Peripheral Data I/O Register, the buffer
is actually being read. During an overrun condi-
tion, when the Master device has sent several
bytes of data and the Slave device has not inter-
nally responded to clear the first SPIF, only the
first byte is contained in the receive buffer of the
Slave device; all others are lost. The user may
read the buffer at any time. The first SPIF must be
cleared by the time a second transfer of data from
the shift register to the read buffer is initiated, oth-
erwise an overrun condition will exist.
A write to the Serial Peripheral Data I/O Register is
not buffered, and data is placed directly in the shift
register for transmission.
The ability to access the Serial Peripheral Data I/O
Register is limited when a transmission is taking
place. Please refer to the description of the WCOL
and SPIF status bits inorder to fully appreciate the
rules governing the use of the Serial Peripheral
Data I/O Register.
4.4.10
Configurations
There are two types of SPI systems, single Master
and Multimaster.
A typical Single Master system may be configured,
using one MCU as the Master and four others as
Slaves. The MOSI, MISO and SCK pins are all
wired to equivalent pins on each device. The Mas-
ter device generates the SCK clock, whereas the
Slave devices all receive it. Since the MCU Master
device is the bus Master, it internally controls the
function of its MOSI and MISO lines, thus writing
data to the Slave devices on the MOSI and read-
ing data from the Slave devices on the MISO lines.
The Master device selects the individual Slave de-
vices by using four pins of a parallel port to control
the four SS pins of the Slave devices. A Slave de-
vice is selected when the Master device pulls its
SS pin low. The SS pins are pulled high, thus dis-
abling the Slave devices during Reset, since the
Master device ports will be forced as inputs.
Note that Slave devices need not be enabled in a
mutually exclusive fashion, except in order to pre-
vent bus contention on the MISO lines. An exam-
ple of this is a write to several display drivers to
clear a display using a single I/O operation.
To ensure that proper data transmission takes
place between the Master device and a Slave de-
vice, the Master device may ask the Slave device
to respond by echoing a previously received data
byte (this data byte can be inverted, or at least be
different from the last one sent by the Master de-
vice). The Master device will always receive the
previous byte back from the Slave if all MISO and
MOSI lines are connected and the Slave has not
written its data I/O register. Other transmission se-
curity methods may be defined using ports as
handshake lines, or by means of data bytes con-
taining command fields.
A Multimaster system may also be configured by
the user. An exchange of Master control can be
implemented by adopting a handshake scheme
using the I/O ports, or by an exchange of code
messages via the Serial Peripheral Interface sys-
tem. The principal device controls are the MSTR
bit in the Serial Peripheral Control Register and
the MODF bit in the Serial Peripheral Status Reg-
ister.
Single
Master
And
Multimaster
7
0
X
X
X
X
X
X
X
X
相關PDF資料
PDF描述
ST72T85A5Q6 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES
ST730C08L3 PHASE CONTROL THYRISTORS
ST730C08L3L PHASE CONTROL THYRISTORS
ST730C12L0 PHASE CONTROL THYRISTORS
ST730C12L0L PHASE CONTROL THYRISTORS
相關代理商/技術參數
參數描述
ST7-28B56 功能描述:電源變壓器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in
ST72A 制造商:DGS 功能描述:
ST72C104G1B6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72C104G1M1 制造商:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER - Bulk
ST72C104G1M6 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*