- 您現在的位置：買賣IC網 > PDF目錄385871 > ST7285C (意法半導體) 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES PDF資料下載
參數資料
| 型號： | ST7285C |
| 廠商： | 意法半導體 |
| 英文描述： | 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES |
| 中文描述： | 8位微控制器48,000鐵路發展策略光盤，3K內存，ADC，兩個定時器，2個SPI，I2C和脊髓損傷接口 |
| 文件頁數： | 24/117頁 |
| 文件大?。?/td> | 748K |
| 代理商： | ST7285C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
24/117
ST7285C
4 ON-CHIP PERIPHERALS
4.1 I/O PORTS
4.1.1 Introduction
Each I/O Port can contain up to 8 individually pro-
grammable I/Os. The MCU features seven 8-bit
Ports (A, B, C,... G) and one 6-bit-port (H). Each I/
O pin is dedicated to its main functionality, thus re-
ducing and simplifying its programmability.
The current chapter describes the generic I/O
structure used in the MCU.
All I/Os are based on a generic circuit, of which a
block diagram is given inFigure 13. In most cases
the functions are simplified, and several sub-
blocks may be missing (such as, for instance, the
analog switch on ports B to H or pull-up and inter-
rupt logic for most of the I/O ports). Some registers
may also be absent where their functionality is re-
dundant: it is therefore advisable to consult the
Memory Map in section1.3 and the pin description
in section 1.2 for proper use of any particular I/O.
Only ports C4, C5, D4, D5, F0,F1, F2, F3, G3 fea-
ture interrupt capability.
The following sub-section 4.1.2 contains generic
information on ST7 I/O ports. For information spe-
cific to this device, please refer to sub-section
4.1.3.
4.1.2 Generic I/O Features
The I/O ports offer the following generic features:
– inputs with Schmitt trigger
– analog inputs, when connected via internal mul-
tiplexer
– interrupt generation, maskable by software
– EMI compliance thanks to reduced noise radia-
tion due to lowered cross-current in push pull
mode and reduced input susceptibility. This fea-
ture is particularly relevant in RDS applications.
Each generic I/O pin may be individually program-
mable by software as:
– input: no pull-up, no interrupt generation
– input: pull-up, no interrupt generation
– input: pull-up, interrupt generation
– input: pull-down, no interrupt generation
– output: push-pull
– output: open-drain, no pull-up
– output: open-drain, with pull-up
4.1.2.1 Port Registers
Each port may be associated with up to four regis-
ters:
–
DATA REGISTER
(DR)
Address 0000 0000 000x xx00b; always present.
–
DATA DIRECTION REGISTER
(DDR)
Address 0000 0000 000x xx01b; always present.
–
OPTION REGISTER
(OR)
Address 0000 0000 000x xx10b; depending on
I/O dedication.
–
PULL-UP REGISTER
(PUR)
Address 0000 0000 000x xx11b; depending on
I/O dedication.
These are not internal CPU registers and must be
accessed by reading and writing to the relevant
memory locations. Refer toTable 1- Memory Map
for the respective addresses and reset values.
4.1.2.2 Functional Description
Each I/O pin may be programmed independently
as an analog input if the port features analog capa-
bilities, as a digital input or a digital output with var-
ious variants, using the corresponding register
bits.When programmed as a digital input, a pull-up
or a pull-down resistor can, if present, be activated
by software. Only when enabling the pull-up, can
an interrupt function be programmed by software.
When programmed as an output, the I/O pin can
be programmed to operate either in push-pull or in
open-drain mode.
The interrupts generated by a port (active low) are
“ORed” to a single interrupt line that can be routed
to a CPU interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| ST72T85A5Q6 | 8-BIT MCU FOR RDS WITH 48K ROM, 3K RAM, ADC, TWO TIMERS, TWO SPIs, I2C AND SCI INTERFACES |
| ST730C08L3 | PHASE CONTROL THYRISTORS |
| ST730C08L3L | PHASE CONTROL THYRISTORS |
| ST730C12L0 | PHASE CONTROL THYRISTORS |
| ST730C12L0L | PHASE CONTROL THYRISTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7-28B56 | 功能描述:電源變壓器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率額定值:12 VA 初級電壓額定值:115 V / 230 V 次級電壓額定值:12 V / 24 V 安裝風格:SMD/SMT 一次繞組:Dual Primary Winding 二次繞組:Dual Secondary Winding 長度:2.5 in 寬度:2 in 高度:1.062 in |
| ST72A | 制造商:DGS 功能描述: |
| ST72C104G1B6 | 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST72C104G1M1 | 制造商:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER - Bulk |
| ST72C104G1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。