- 您現在的位置：買賣IC網 > PDF目錄359235 > MT90866AG2 (ZARLINK SEMICONDUCTOR INC) Flexible 4 K x 2.4 K Channel Digital Switch with H.110 Interface and 2.4 K x 2.4 K Local Switch PDF資料下載
參數資料
| 型號： | MT90866AG2 |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 路由/交換 |
| 英文描述： | Flexible 4 K x 2.4 K Channel Digital Switch with H.110 Interface and 2.4 K x 2.4 K Local Switch |
| 中文描述： | TELECOM, DIGITAL TIME SWITCH, PBGA344 |
| 封裝： | 27 X 27 MM, LEAD FREE, PLASTIC, MS-034, BGA-344 |
| 文件頁數： | 44/86頁 |
| 文件大?。?/td> | 701K |
| 代理商： | MT90866AG2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
MT90866
Data Sheet
44
Zarlink Semiconductor Inc.
19.7 Phase Slope
The phase slope or the phase alignment speed is the rate at which a given signal changes phase with respect to an
ideal signal. The given signal is typically the output signal. The ideal signal is of constant frequency and is nominally
equal to the value of the final output signal or final input signal. Many telecom standards like Telcordia
GR-1244-CORE state that the phase slope may not exceed a certain value, usually 81 ns/1.327 ms (61 ppm). This
can be achieved by limiting the phase detector output to 61ppm or less.
In the DPLL when operating in primary master mode the Phase Slope Limiter Circuit achieves the maximum phase
slope to be: 56 ppm or 7.0 ns/125 us. When operating in secondary master or slave mode the output edges follow
the input edges in accordance with the H.110 standard
19.8 Maximum Time Interval Error (MTIE)
MTIE is the maximum peak to peak delay between a given timing signal and an ideal timing signal within a
particular observation period.
For the DPLL, the maximum time interval error is less than 21 ns per reference switch.
19.9 Phase Lock Time
The Phase Lock Time is the time it takes the PLL to phase lock to the input signal. Phase lock occurs when the
input and the output signals are not changing in phase with respect to each other (not including jitter).
Lock time is very difficult to determine because it is affected by many factors which include:
i) initial input to output phase difference
ii) initial input to output frequency difference
iii) PLL loop filter
iv) PLL limiter
Although a short phase lock time is desirable, it is not always possible to achieve due to other PLL requirements.
For instance, better jitter transfer performance is achieved with a lower frequency loop filter which increases lock
time, but better (smaller) phase slope performance (limiter) results in longer lock times. The DPLL loop filter and
limiter were optimized to meet the Telcordia GR-499-CORE jitter transfer and Telcordia GR-1244-CORE phase
alignment speed requirements. Consequently, phase lock time, which is not a standards requirement, is less than
50 seconds.
20.0 Initialization of the MT90866
During power up, the TRST pin should be pulled low to ensure that the MT90866 is in the functional mode. An
external pull-down resistor is required on this pin so that the MT90866 will not enter the JTAG test mode during
power up.
After power up, the contents of the connection memory can be in any state. The ODE pin should be held low after
power up to keep all serial outputs in a high impedance state until the microprocessor has initialized the switching
matrix. This procedure prevents two serial outputs from driving the same stream simultaneously.
During the microprocessor initialization routine, the microprocessor should program the desired active paths
through the switch. The memory block programming feature can also be used to quickly initialize the backplane and
local connection memories.
When this process is completed, the microprocessor controlling the MT90866 can bring the ODE pin high to
relinquish the high impedance state control.
相關PDF資料 |
PDF描述 |
|---|---|
| MT90869 | Flexible 16K Digital Switch (F16kDX) |
| MT90869AG | Flexible 16K Digital Switch (F16kDX) |
| MT90870 | Flexible 12 k Digital Switch (F12kDX) |
| MT90871AV | Flexible 8K Digital Switch (F8KDX) |
| MT90871 | Flexible 8K Digital Switch (F8KDX) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90866AL | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:WAN Access Switch |
| MT90868AG | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 32KX8K/8KX8K/1K X 1K 1.8V/3.3V 466BGA - Trays |
| MT90868AG2 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 32KX8K/8KX8K/1K X 1K 1.8V/3.3V 466BGA - Trays |
| MT90869 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Flexible 16K Digital Switch (F16kDX) |
| MT90869AG | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 16KX16K/8KX8K 1.8V/3.3V 272BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH F16KDX 272PBGA 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH F16KDX 272PBGA |
發布緊急采購，3分鐘左右您將得到回復。