- 您現在的位置：買賣IC網 > PDF目錄384759 > MT90221AL (Mitel Networks Corporation) Quad IMA/UNI PHY Device PDF資料下載
參數資料
| 型號： | MT90221AL |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Quad IMA/UNI PHY Device |
| 中文描述： | 四IMA的/單向物理層設備 |
| 文件頁數： | 29/114頁 |
| 文件大?。?/td> | 304K |
| 代理商： | MT90221AL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
MT90221
21
reported negative. A delay is negative when the two
most significant bits are set to "1". The value
reported is with respect to the read pointer and
represents the minimum number of cells that has to
be added to the present guardband before adding
the link in the IMA group. See paragraph 3.3.10.6
Incrementing/Decrementing the Recombiner Delay
for more details.
If a link to be added is faster and would cause its
write pointer to be set beyond the
RX Maximum
operational Delay
programmed value, then the link
is reported to be faulty through an LODS condition.
The recombination process will not be affected as
long as the amount of delay is not larger than the
total number of cells in the external memory.
LODS will also be reported if, during operation, the
delay of a link is changing to exhibits higher or lower
delay which result in a negative delay value or
beyond the RX Maximum Operating Delay value.
LODS events are reported by the
IRQ Link Status
register and the selected
Current Maximum Delay
register for an IMA Group.
3.3.10.4 Negative Delay Values
If the recombiner process is enabled for a link that is
exhibiting a negative delay value then the
recombiner process will be suspended until the write
pointers are moved in such a way that the delay is
reported with a positive value of 4. At this time the
recombiner process will resume. No cells are lost.
The same behavior applies if the delay value of a
link which is part of the round robin process
(recombiner bit ON) goes negative: the recombiner
process will be suspended until the delay value
becomes positive with a value of 4. The latter
condition can happen under severe error conditions
if the recombiner process of the faulty link is not
disabled.
3.3.10.5 Measured Delay Between Links
The values and delay type for a selected link(s) or
IMA Group can be read using the
RX Delay Select
register.
IMA Group delay types include: the
Maximum Delay
over time
; the
Current Maximum Delay
and the
Current Minimum Delay
of an IMA Group.
Current
Link delay
reports the
Current Delay
of a link.
These values are all reported through a common
RX
Delay
register. The value is in number of cells. All
the delay values include the guardband delay value.
The
RX Delay Link Number
register is reporting the
link number associated with the delay value that is
currently in the
RX Delay
registers, with the
exception for the Maximum Delay over time value,
where the link number reported is not valid (reports
value of 0).
The
Maximum Delay over time
value can be reset at
any time by writing a clear command to bit 5 in the
RX
Delay Select
register. The differential delays can be
easily obtained by subtracting the delay values of the
links.
3.3.10.6 Incrementing/Decrementing the
Recombiner Delay
If a link to be added has a delay value which falls
beyond the worst current delay value, then there are
2 options: either reject the link or re-adjust the
pointers. To readjust the pointers, the number of cells
to be added (delta) is specified and corresponds to
the amount of extra delay to be added to the current
recombination delay. The additional delay is first
programmed in the
Guardband/Delta Delay
register
and then a command to increase the delay is issued
(using the
Increment/Decrement Delay Control
register). The MT90221 device stops the recombiner
process for the amount of time specified and then
resumes the recombiner process. No cells are lost
but there is an effect on the CDV. The increment
process is completed when the control bit in the
Increment/Decrement Delay Control
register is
returned to a 0 value.
If the link exhibiting the longest transmission delay is
removed, the recombiner delay can be reduced
accordingly. When such a correction occurs, the
number of cells corresponding to the delay correction
will be lost. To reduce the impact of this correction,
its implementation can either be immediate or
delayed. The
Increment/Decrement Delay Control
register is used for this purpose. The amount of
delay to be removed (i.e., number of cells) in the
recombiner process is controlled by the
Guardband/
Delta Delay
register. Alternatively, the links can all
be placed in blocking mode for the transition period
to avoid losing any cells.
If a decrement delay command is issued which
would result in a negative delay value on one or
more links, the following action will take place: the
read pointer is re-adjusted as required by the
decrease delay command and since the delay is
negative, the recombiner process is suspended until
the delay on all the link are at least reaching a
positive value of 4. Then, the recombiner process will
resume.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9041B | T1/E1 System Synchronizer |
| MT9041BP | T1/E1 System Synchronizer |
| MT9041 | Multiple Output Trunk PLL |
| MT9041AP | IC REG LDO 150MA 5.0V 0.5% 8SOIC |
| MT9042C | Multitrunk System Synchronizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90222 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:4/8/16 Port IMA/TC PHY Device |
| MT90222AG | 制造商:Microsemi Corporation 功能描述:ATM IMA 40MBPS 2.5V 384BGA - Trays |
| MT90222AG2 | 制造商:Microsemi Corporation 功能描述:ATM IMA 40MBPS 2.5V 384BGA /BAKE/DRYPACK - Trays |
| MT90223AG | 制造商:Microsemi Corporation 功能描述:ATM IMA 80MBPS 2.5V 384BGA - Trays |
| MT90223AG2 | 制造商:Microsemi Corporation 功能描述:ATM IMA 80MBPS 2.5V 384BGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。