- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C754B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C754B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大）64字節的FIFO |
| 文件頁數： | 18/50頁 |
| 文件大小： | 259K |
| 代理商： | SC16C754B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
9397 750 14668
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 13 June 2005
18 of 50
Philips Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
6.6.2
Block DMA transfers (DMA mode 1)
Figure 12
shows TXRDY and RXRDY in DMA mode 1.
6.6.2.1
Transmitter
TXRDY is active when there is a trigger level number of spaces available. It becomes
inactive when the FIFO is full.
6.6.2.2
Receiver
RXRDY becomes active when the trigger level has been reached, or when a time-out
interrupt occurs. It will go inactive when the FIFO is empty or an error in the RX FIFO is
flagged by LSR[7].
6.7 Sleep mode
Sleep mode is an enhanced feature of the SC16C754B UART. It is enabled when EFR[4],
the enhanced functions bit, is set
and
when IER[4] is set. Sleep mode is entered when:
The serial data input line, RX, is idle (see
Section 6.8 “Break and time-out
conditions”
).
The TX FIFO and TX shift register are empty.
There are no interrupts pending except THR and time-out interrupts.
Remark:
Sleep mode will
not
be entered if there is data in the RX FIFO.
In Sleep mode, the UART clock and baud rate clock are stopped. Since most registers are
clocked using these clocks, the power consumption is greatly reduced. The UART will
wake up when any change is detected on the RX line, when there is any change in the
state of the modem input pins, or if data is written to the TX FIFO.
Remark:
Writing to the divisor latches, DLL and DLH, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLH.
Fig 12. TXRDY and RXRDY in DMA mode 1
TX
wrptr
wrptr
TXRDY
FIFO full
TXRDY
RX
rdptr
rdptr
FIFO EMPTY
RXRDY
RXRDY
002aaa869
trigger
level
trigger
level
相關PDF資料 |
PDF描述 |
|---|---|
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
| SCAN18374TSSC | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C754BIA68 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,518 | 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,529 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68512 | 制造商:NXP Semiconductors 功能描述:IC QUAD UART FIFO 5MBPS 5.5V LCC-68 |
發布緊急采購，3分鐘左右您將得到回復。