- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C754B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C754B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大）64字節的FIFO |
| 文件頁數： | 11/50頁 |
| 文件大?。?/td> | 259K |
| 代理商： | SC16C754B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
9397 750 14668
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 13 June 2005
11 of 50
Philips Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
6.2.1
Auto-RTS
Auto-RTS data flow control originates in the receiver block (see
Figure 1 “Block diagram of
SC16C754B” on page 3
).
Figure 6
shows RTS functional timing. The receiver FIFO trigger
levels used in Auto-RTS are stored in the TCR. RTS is active if the RX FIFO level is below
the halt trigger level in TCR[3:0]. When the receiver FIFO halt trigger level is reached,
RTS is deasserted. The sending device (for example, another UART) may send an
additional byte after the trigger level is reached (assuming the sending UART has another
byte to send) because it may not recognize the deassertion of RTS until it has begun
sending the additional byte. RTS is automatically reasserted once the receiver FIFO
reaches the resume trigger level programmed via TCR[7:4]. This reassertion allows the
sending device to resume transmission.
6.2.2
Auto-CTS
The transmitter circuitry checks CTS before sending the next data byte. When CTS is
active, the transmitter sends the next byte. To stop the transmitter from sending the
following byte, CTS must be deasserted before the middle of the last stop bit that is
currently being sent. The auto-CTS function reduces interrupts to the host system. When
flow control is enabled, CTS level changes do not trigger host interrupts because the
device automatically controls its own transmitter. Without auto-CTS, the transmitter sends
any data present in the transmit FIFO and a receiver overrun error may result.
(1) N = receiver FIFO trigger level.
(2) The two blocks in dashed lines cover the case where an additional byte is sent, as described in
Section 6.2.1
.
Fig 6.
RTS functional timing
Start
byte N
Start
byte N
+
1
Start
Stop
Stop
RX
RTS
IOR
N
N+1
1
2
002aaa226
(1) When CTS is LOW, the transmitter keeps sending serial data out.
(2) When CTS goes HIGH before the middle of the last stop bit of the current byte, the transmitter finishes sending the current
byte, but it does not send the next byte.
(3) When CTS goes from HIGH to LOW, the transmitter begins sending data again.
Fig 7.
CTS functional timing
Start
byte 0 to 7
Stop
TX
CTS
002aaa227
Start
byte 0 to 7
Stop
相關PDF資料 |
PDF描述 |
|---|---|
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
| SCAN18374TSSC | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C754BIA68 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,518 | 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,529 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68512 | 制造商:NXP Semiconductors 功能描述:IC QUAD UART FIFO 5MBPS 5.5V LCC-68 |
發布緊急采購，3分鐘左右您將得到回復。