參數資料
型號： SC16C754B
廠商： NXP Semiconductors N.V.
英文描述： 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
中文描述： 5伏，3.3伏和2.5伏兆5四異步/秒（最大）64字節的FIFO
文件頁數： 12/50頁
文件大?。?/td> 259K
代理商： SC16C754B
9397 750 14668
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 13 June 2005
12 of 50
Philips Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
6.3 Software flow control
Software flow control is enabled through the enhanced feature register and the modem
control register. Different combinations of software flow control can be enabled by setting
different combinations of EFR[3:0].
Table 3
shows software flow control options.
Remark:
When using software flow control, the Xon/Xoff characters cannot be used for
data characters.
There are two other enhanced features relating to software flow control:
Xon Any function (MCR[5]):
Operation will resume after receiving any character
after recognizing the Xoff character. It is possible that an Xon1 character is
recognized as an Xon Any character, which could cause an Xon2 character to be
written to the RX FIFO.
Special character (EFR[5]):
Incoming data is compared to Xoff2. Detection of the
special character sets the Xoff interrupt (IIR[4]) but does not halt transmission. The
Xoff interrupt is cleared by a read of the IIR. The special character is transferred to the
RX FIFO.
6.3.1
RX
When software flow control operation is enabled, the SC16C754B will compare incoming
data with Xoff1/Xoff2 programmed characters (in certain cases, Xoff1 and Xoff2 must be
received sequentially). When the correct Xoff character is received, transmission is halted
after completing transmission of the current character. Xoff detection also sets IIR[4] (if
enabled via IER[5]) and causes INT to go HIGH.
To resume transmission, an Xon1/Xon2 character must be received (in certain cases
Xon1 and Xon2 must be received sequentially). When the correct Xon characters are
received, IIR[4] is cleared, and the Xoff interrupt disappears.
Table 3:
EFR[3]
0
1
0
1
X
X
X
1
Software flow control options (EFR[3:0])
EFR[2]
EFR[1]
EFR[0]
0
X
X
0
X
X
1
X
X
1
X
X
X
0
0
X
1
0
X
0
1
0
1
1
TX, RX software flow controls
no transmit flow control
transmit Xon1, Xoff1
transmit Xon2, Xoff2
transmit Xon1, Xon2, Xoff1, Xoff2
no receive flow control
receiver compares Xon1, Xoff1
receiver compares Xon2, Xoff2
transmit Xon1, Xoff1
receiver compares Xon1 or Xon2, Xoff1 or Xoff2
transmit Xon2, Xoff2
receiver compares Xon1 or Xon2, Xoff1 or Xoff2
transmit Xon1, Xon2, Xoff1, Xoff2
receiver compares Xon1 and Xon2, Xoff1 and Xoff2
no transmit flow control
receiver compares Xon1 and Xon2, Xoff1 and Xoff2
0
1
1
1
1
1
1
1
0
0
1
1
相關PDF資料
PDF描述
SC68C752B 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface
SCAN182245AMTD Non-Inverting Transceiver with 25ohm Series Resistor Outputs
SCAN18245TSSC Non-Inverting Transceiver with 3-STATE Outputs
SCAN18374T D-Type Flip-Flop with 3-STATE Outputs
SCAN18374TSSC D-Type Flip-Flop with 3-STATE Outputs
相關代理商/技術參數
參數描述
SC16C754BIA68 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,518 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,529 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68512 制造商:NXP Semiconductors 功能描述:IC QUAD UART FIFO 5MBPS 5.5V LCC-68
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*