參數資料
型號: ORCAORT82G5
英文描述: 1.0?.25/2.0?.5/3.125 Gbits/s Backplane Interface FPSC
中文描述: 1.0?.25/2.0?.5/3.125 Gb /秒背板接口促進文化基金
文件頁數: 42/90頁
文件大?。?/td> 1915K
代理商: ORCAORT82G5
ORCAORT4622 FPSC
Four-Channel x 622 Mbits/s Backplane Transceiver
Preliminary Data Sheet
March 2000
42
L Lucent Technologies Inc.
HSI Circuit Specifications
(continued)
Power Supply Decoupling LC Circuit
The 622 MHz HSI macro contains both analog and digital circuitry. The data recovery function, for example, is
implemented as primarily a digital function, but it relies on a conventional analog phase-locked loop to provide its
622 MHz reference frequency. The internal analog phase-locked loop contains a voltage-controlled oscillator. This
circuit will be sensitive to digital noise generated from the rapid switching transients associated with internal logic
gates and parasitic inductive elements. Generated noise that contains frequency components beyond the band-
width of the internal phase-locked loop (about 3 MHz) will not be attenuated by the phase-locked loop and will
impact bit error rate directly. Thus, separate power supply pins are provided for these critical analog circuit ele-
ments.
Additional power supply filtering in the form of a LC pi filter section will be used between the power supply source
and these device pins as shown in Figure 13. The corner frequency of the LC filter is chosen based on the power
supply switching frequency, which is between 100 kHz and 300 kHz in most applications.
Capacitors C1 and C2 are large electrolytic capacitors to provide the basic cutoff frequency of the LC filter. For
example, the cutoff frequency of the combination of these elements might fall between 5 kHz and 50 kHz. Capaci-
tor C3 is a smaller ceramic capacitor designed to provide a low-impedance path for a wide range of high-frequency
signals at the analog power supply pins of the device. The physical location of capacitor C3 must be as close to the
device lead as possible. Multiple instances of capacitors C3 can be used if necessary. The recommended filter for
the HSI macro is shown below: L = 4.7
μ
H, RL = 1
, C1 = 0.01
μ
F, C2 = 0.01
μ
F, C3 = 4.7
μ
F.
5-9344(F)
Figure 13. Sample Power Supply Filter Network for Analog HSI Power Supply Pins
C2
+
C3
+
TO DEVICE
PLL_VDDA
PLL_VSSA
C1
+
FROM POWER
SUPPLY SOURCE
L
相關PDF資料
PDF描述
ORCAORT8850 Single 2.3V PNP in OP, I temp, -40C to +85C, 8-MSOP, T/R
ORD211 REED SWITCH
ORD221 REED SWITCH
ord9216 Reed Switch(舌簧開關)
ORD9702R5 Optoelectronic
相關代理商/技術參數
參數描述
ORD 228VL/25-27 AT 功能描述:磁性/簧片開關 REED SWITCH Single-contact RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
ORD Module 制造商:Emerson Network Power - Embedded Power 功能描述:ORD MODULE - Bulk
ORD# 10549117 制造商:Amphenol Corporation 功能描述:ORD# 10549117-PER DAN D. - Bulk
ORD211 制造商:MEDER 制造商全稱:Meder Electronic 功能描述:REED SWITCH
ORD211(0810) 制造商:OKI Semiconductor 功能描述: