- 您現在的位置：買賣IC網 > PDF目錄370584 > HIP8112A (Harris Corporation) NTSC/PAL Video Decoder PDF資料下載
參數資料
| 型號： | HIP8112A |
| 廠商： | Harris Corporation |
| 英文描述： | NTSC/PAL Video Decoder |
| 中文描述： | NTSC / PAL視頻解碼器 |
| 文件頁數： | 9/40頁 |
| 文件大?。?/td> | 719K |
| 代理商： | HIP8112A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
4-9
exceed 285. Greater than 285 lines in a field is interpreted
as a PAL video source. An ideal NTSC source should have
262.5 lines per field and a PAL source should have 312.5
lines per field.
The HMP8112A can detect a STANDARD ERROR that sig-
nals when the video received does not match the standard
that was programmed into the Video Input Control Register.
This flag, when asserted, tells the user that the video stan-
dard that was expected was not found and a different stan-
dard should be selected in the Video Input Control register.
The error flag is cleared after a RESET or after the Chroma
PLL Clock Ratio register has been loaded via the I
2
C bus.
After the flag is cleared the standard error logic verifies the
video standard. The error flag is set after 2 vertical sync peri-
ods have passed and the line count did not match the
expected line count.
Video Adjustments
The HMP8112A allows the user to vary such video parame-
ters as Contrast, Brightness, Sharpness, Hue and Color Sat-
uration. These adjustments can be made via the I
2
C
interface. Contrast, brightness and sharpness are luminance
controls. The full dynamic range of the luminance channel
can be used by selecting the IRE setup cancellation mode.
This mode will remove the IRE setup and blanking level off-
set to take advantage of the full dynamic range of the lumi-
nance processing path. The sharpening filters allow the
enhancement of low, mid and high frequency components of
the luminance signal to compensate for low amplitude video.
Vertical sharpness is also controlled via the I
2
C interface.
Hue and Color saturation controls enhance the CbCr compo-
nents of the incoming video, all under user control.
Luminance Adjustments
The Luminance data can be adjusted in the HMP8112A. The
user can adjust brightness and contrast of the Y or lumi-
nance data. The user can also set the IRE or setup subtrac-
tion value to eliminate the black pedestal offset from NTSC
signals. The Contrast adjustment range can exceed a value
of one so as to take full advantage of the 8-bit dynamic range
for Y. The user control settings executes the equation
Y
OUT
= (Y - IRE Setup + BRIGHTNESS) x CONTRAST
Brightness
The user can control the brightness of the incoming video by
programming the Brightness register. The brightness adjust-
ment will offset the Y component. The brightness register is
an 8-bit register where the bottom 7 bits are brightness con-
trol and the top bit enables NTSC 7.5 IRE black setup can-
cellation.
When the IRE bit is set (1) for NTSC, then 73 is subtracted
from the Y data. If the IRE bit is cleared (0) for PAL, then 64
is subtracted. The brightness control bits BR[6-0] will
brighten the picture as the value is increased. BR = -64 is the
darkest and BR = +63 is the brightest. The default value of
the register after a RESET is 0 (80
H
).
Contrast
The contrast adjustment will allow the user to increase and
decrease the gain of the Y data. The contrast factor is an 8-
bit number (as shown below) that ranges from 0 to 1.992.
X.XXXXXXX
The default register value of 1.4766 (0xBD) is calculated as
follows:
Register = Factor * 128 = 1.4766 * 128 = 189 = 0xBD
TABLE 1. COMPATIBLE VIDEO INPUT STANDARDS
STANDARD
COLOR
SUBCARRIER
f
SC
27MHz
PLL
Ratio
24.54MHz
PLL
Ratio
FIELDS/
SECOND
VERTICAL
LINES
LINE
FREQUENCY
NOMINAL
BANDWIDTH
BLACK
SETUP TO
BLANK
NTSC
(M)
3.579545MHz
0x87C1
0x955D
60Hz
525
15,734
(
±
0.0003%)
4.2MHz
7.5 IRE
PAL
(B, D, G, H, I)
4.43361875MHz
0xA826
0xB901
50Hz
625
15,625
(
±
0.02%)
5.0MHz
0 IRE
PAL
(M)
3.57561149MHz
0x879B
0x9533
60Hz
525
15,750
(
±
0.0003%)
4.2MHz
7.5 IRE
PAL
(N)
4.43361875MHz
0xA826
0xB901
50Hz
625
15,625
(
±
0.15%)
4.2MHz
7.5 IRE
PAL Special
Combination N
3.58205625MHz
0x97DA
0x9578
50Hz
625
15,750
(
±
0.15%)
4.2MHz
7.5 IRE
IRE BLACK SETUP
(NTSC = 73, PAL = 64)
+
+
-
X
BRIGHTNESS
(-64 TO +63)
CONTRAST
(0 TO 1.999)
Y DATA
FROM
DECODER
Y’
8
FIGURE 10. LUMINANCE CONTROL SETTINGS PATH
HMP8112A
相關PDF資料 |
PDF描述 |
|---|---|
| HIR19-21C | Technical Data Sheet 0.8mm Height Flat Top Infrared LED |
| HIR19-L11 | Technical Data Sheet 0.8mm Height Flat Top Infrared LED |
| HIR204C | 3mm Infrared LED, T-1 |
| HIR | 5mm Infrared LED, T-1 3/4 |
| HIR333 | 5mm Infrared LED, T-1 3/4 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP-8V | 制造商:Belden Inc 功能描述:SPLITTER 8 WAY |
| HIP9010 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9010AB | 制造商:Intersil Corporation 功能描述: |
| HIP9011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。