參數資料
型號： DV164136
廠商： Microchip Technology
文件頁數： 77/107頁
文件大小： 0K
描述： DEVELOPMENT KIT FOR PIC18
產品培訓模塊： PIC18 J Series MCU Overview
標準包裝： 1
系列： PIC®
類型： MCU
適用于相關產品： PIC18F8722，PIC18F87J11
所含物品： 板，線纜，CD，PICkit? 3 個編程器，電源
產品目錄頁面： 659 (CN2011-ZH PDF)
相關產品： PIC18F87J11-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F87J11T-I/PTTR-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722T-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722-E/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722T-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
PIC18F8722-I/PT-ND - IC PIC MCU FLASH 64KX16 80TQFP
2007-2012 Microchip Technology Inc.
DS39778E-page 71
PIC18F87J11 FAMILY
6.1.5
PROGRAM COUNTER
The Program Counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 21 bits wide
and is contained in three separate 8-bit registers. The
low byte, known as the PCL register, is both readable
and writable. The high byte, or PCH register, contains
the PC<15:8> bits; it is not directly readable or writable.
Updates to the PCH register are performed through the
PCLATH register. The upper byte is called PCU. This
register contains the PC<20:16> bits; it is also not
directly readable or writable. Updates to the PCU
register are performed through the PCLATU register.
The contents of PCLATH and PCLATU are transferred
to the Program Counter by any operation that writes
PCL. Similarly, the upper two bytes of the Program
Counter are transferred to PCLATH and PCLATU by an
operation that reads PCL. This is useful for computed
offsets to the PC (see Section 6.1.8.1 “Computed
The PC addresses bytes in the program memory. To
prevent the PC from becoming misaligned with word
instructions, the Least Significant bit of PCL is fixed to
a value of ‘0’. The PC increments by 2 to address
sequential instructions in the program memory.
The CALL, RCALL, GOTO and program branch
instructions write to the Program Counter directly. For
these instructions, the contents of PCLATH and
PCLATU are not transferred to the Program Counter.
6.1.6
RETURN ADDRESS STACK
The return address stack allows any combination of up
to 31 program calls and interrupts to occur. The PC is
pushed onto the stack when a CALL or RCALL instruc-
tion is executed, or an interrupt is Acknowledged. The
PC value is pulled off the stack on a RETURN, RETLW
or a RETFIE instruction (and on ADDULNK and
SUBULNK
instructions if the extended instruction set is
enabled). PCLATU and PCLATH are not affected by
any of the RETURN or CALL instructions.
The stack operates as a 31-word by 21-bit RAM and a
5-bit Stack Pointer, STKPTR. The stack space is not
part of either program or data space. The Stack Pointer
is readable and writable and the address on the top of
the stack is readable and writable through the
Top-of-Stack Special Function Registers. Data can also
be pushed to, or popped from, the stack using these
registers.
A CALL type instruction causes a push onto the stack.
The Stack Pointer is first incremented and the location
pointed to by the Stack Pointer is written with the
contents of the PC (already pointing to the instruction
following the CALL). A RETURN type instruction causes
a pop from the stack. The contents of the location
pointed to by the STKPTR are transferred to the PC
and then the Stack Pointer is decremented.
The Stack Pointer is initialized to ‘00000’ after all
Resets. There is no RAM associated with the location
corresponding to a Stack Pointer value of ‘00000’; this
is only a Reset value. Status bits indicate if the stack is
full, has overflowed or has underflowed.
6.1.6.1
Top-of-Stack (TOS) Access
Only the top of the return address stack is readable and
writable. A set of three registers, TOSU:TOSH:TOSL,
hold the contents of the stack location pointed to by the
STKPTR register (Figure 6-4). This allows users to
implement a software stack if necessary. After a CALL,
RCALL
or interrupt (and ADDULNK and SUBULNK
instructions if the extended instruction set is enabled),
the software can read the pushed value by reading the
TOSU:TOSH:TOSL registers. These values can be
placed on a user-defined software stack. At return
time, the software can return these values to
TOSU:TOSH:TOSL and do a return.
The user must disable the Global Interrupt Enable bits
while accessing the stack to prevent inadvertent stack
corruption.
FIGURE 6-4:
RETURN ADDRESS STACK AND ASSOCIATED REGISTERS
00011
001A34h
11111
11110
11101
00010
00001
00000
00010
Return Address Stack <20:0>
Top-of-Stack
000D58h
TOSL
TOSH
TOSU
34h
1Ah
00h
STKPTR<4:0>
Top-of-Stack Registers
Stack Pointer
相關PDF資料
PDF描述
GBM25DCWT CONN EDGECARD 50POS DIP .156 SLD
GCM24DCTN CONN EDGECARD 48POS DIP .156 SLD
1435863-2 PATCHCORD CAT6 YLW/YLW BOOT 2'
1435862-2 PATCHCORD CAT6 RED/RED BOOT 2'
V48C5T50BF3 CONVERTER MOD DC/DC 5V 50W
相關代理商/技術參數
參數描述
DV164139 功能描述:開發板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
DV17K3225T 制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R
DV17K4032T 制造商:SEI Stackpole Electronics Inc 功能描述:VAR 17VAC 22VDC 250A 27V 4032 SMD - Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 250A 27V 4032 SMD T/R
DV18-145MB-3K 功能描述:端子 PIN -DSC 22-18 145X032 VYL RED RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
DV18-145M-C 功能描述:端子 MALE BLADE ADAPT RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*