(PWMDAT1 × t" />
參數資料
型號： USB-I2C/LIN-CONV-Z
廠商： Analog Devices Inc
文件頁數： 66/104頁
文件大小： 0K
描述： USB TO I2C/LIN CONV BOARD
標準包裝： 1
附件類型： 適配器板
適用于相關產品： ARM7TDMI?
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 64 of 104
Both switching edges are moved by an equal amount
(PWMDAT1 × tCORE) to preserve the symmetrical output
patterns.
Also shown are the PWMSYNC pulse and Bit 0 of the
PWMSTA register, which indicates whether operation is in the
first or second half cycle of the PWM period.
The resulting on times of the PWM signals over the full PWM
period (two half periods) produced by the timing unit can be
written as follows:
On the high side
t0HH = PWMDAT0 + 2(PWMCH0 PWMDAT1) × tCORE
t0HL = PWMDAT0 2(PWMCH0 PWMDAT1) × tCORE
and the corresponding duty cycles (d)
d0H = t0HH/tS = + (PWMCH0 PWMDAT1)/PWMDAT0
and on the low side
t0LH = PWMDAT0 2(PWMCH0 + PWMDAT1)
× tCORE
t0LL = PWMDAT0 + 2(PWMCH0 + PWMDAT1)
× tCORE
and the corresponding duty cycles (d)
dOL = t0LH/tS = (PWMCH0 + PWMDAT1)/PWMDAT0
The minimum permissible t0H and t0L values are zero,
corresponding to a 0% duty cycle. In a similar fashion, the
maximum value is tS, corresponding to a 100% duty cycle.
Figure 70 shows the output signals from the timing unit for
operation in double update mode. It illustrates a general case
where the switching frequency, dead time, and duty cycle are all
changed in the second half of the PWM period. The same value
for any or all of these quantities can be used in both halves of the
PWM cycle. However, there is no guarantee that symmetrical
PWM signals are produced by the timing unit in double update
mode. Figure 70 also shows that the dead time insertions into
the PWM signals are done in the same way as in single update
mode.
04
95
5-
0
29
–PWMDAT01 ÷ 2
0H
0L
PWMSYNC
PWMSTA (0)
PWMDAT01
+PWMDAT01 ÷ 2
–PWMDAT02 ÷ 2
+PWMDAT02 ÷ 2
PWMCH02
PWMCH01
2 × PWMDAT12
2 × PWMDAT11
PWMDAT22 + 1
PWMDAT21 + 1
00
PWMDAT02
Figure 70. Typical PWM Outputs of the 3-Phase Timing Unit
(Double Update Mode)
In general, the on times of the PWM signals in double update
mode can be defined as follows:
On the high side
t0HH = (PWMDAT01/2 + PWMDAT02/2 + PWMCH01 +
PWMCH02 PWMDAT11 PWMDAT12) × tCORE
t0HL = (PWMDAT01
/2 + PWMDAT02/2 PWMCH01
PWMCH02 + PWMDAT11 + PWMDAT12) × tCORE
where Subscript 1 refers to the value of that register during the
first half cycle, and Subscript 2 refers to the value during the
second half cycle.
The corresponding duty cycles (d) are
d0H = t0HH/tS = (PWMDAT01
/2 + PWMDAT02/2 +
PWMCH01 + PWMCH02 PWMDAT11 PWMDAT12)/
(PWMDAT01 + PWMDAT02)
On the low side
t0LH = (PWMDAT01/2 + PWMDAT02/2 + PWMCH01 +
PWMCH02 + PWMDAT11 + PWMDAT12) × tCORE
t0LL = (PWMDAT01
/2 + PWMDAT02/2 PWMCH01
PWMCH02 PWMDAT11 PWMDAT12) × tCORE
where Subscript 1 refers to the value of that register during the
first half cycle, and Subscript 2 refers to the value during the
second half cycle.
The corresponding duty cycles (d) are
d0L = t0LH/tS = (PWMDAT01/2 + PWMDAT02/2 +
PWMCH01 + PWMCH02 + PWMDAT11 +
PWMDAT12)/(PWMDAT01 + PWMDAT02)
For the completely general case in double update mode
(see Figure 70), the switching period is given by
tS = (PWMDAT01 + PWMDAT02) × tCORE
Again, the values of t0H and t0L are constrained to lie between
zero and tS.
PWM signals similar to those illustrated in Figure 69 and
Figure 70 can be produced on the 1H, 1L, 2H, and 2L outputs by
programming the PWMCH1 and PWMCH2 registers in a manner
identical to that described for PWMCH0. The PWM controller
does not produce any PWM outputs until all of the PWMDAT0,
PWMCH0, PWMCH1, and PWMCH2 registers have been written
to at least once. When these registers are written, internal
counting of the timers in the 3-phase timing unit is enabled.
Writing to the PWMDAT0 register starts the internal timing of
the main PWM timer. Provided that the PWMDAT0 register is
written to prior to the PWMCH0, PWMCH1, and PWMCH2
registers in the initialization, the first PWMSYNC pulse and
interrupt (if enabled) appear 1.5 × tCORE × PWMDAT0 seconds
after the initial write to the PWMDAT0 register in single update
mode. In double update mode, the first PWMSYNC pulse
appears after PWMDAT0 × tCORE seconds.
相關PDF資料
PDF描述
HBM10DSEI-S13 CONN EDGECARD 20POS .156 EXTEND
EBC35DCSD-S288 CONN EDGECARD 70POS .100 EXTEND
HBM15DRYN-S13 CONN EDGECARD 30POS .156 EXTEND
RBC17DRES-S13 CONN EDGECARD 34POS .100 EXTEND
HBM15DRYH-S13 CONN EDGECARD 30POS .156 EXTEND
相關代理商/技術參數
參數描述
USB-I2C-SS 功能描述:USB 接口集成電路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
USB-ICP-80C51ISP 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC2K 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC9XX 功能描述:程序設計器 - 基于處理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-SAB9 功能描述:插座和適配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*