參數資料
型號: USB-I2C/LIN-CONV-Z
廠商: Analog Devices Inc
文件頁數: 40/104頁
文件大?。?/td> 0K
描述: USB TO I2C/LIN CONV BOARD
標準包裝: 1
附件類型: 適配器板
適用于相關產品: ARM7TDMI?
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 40 of 104
More information relative to the programmer’s model and the
ARM7TDMI core architecture can be found in the following
materials from ARM:
DDI0029G, ARM7TDMI Technical Reference Manual
DDI-0100, ARM Architecture Reference Manual
INTERRUPT LATENCY
The worst-case latency for a fast interrupt request (FIQ)
consists of the following:
The longest time the request can take to pass through the
synchronizer
The time for the longest instruction to complete (the
longest instruction is an LDM) that loads all the registers
including the PC
The time for the data abort entry
The time for FIQ entry
At the end of this time, the ARM7TDMI executes the instruc-
tion at 0x1C (FIQ interrupt vector address). The maximum
total time is 50 processor cycles, which is just under 1.2 s in a
system using a continuous 41.78 MHz processor clock.
The maximum interrupt request (IRQ) latency calculation is
similar but must allow for the fact that FIQ has higher priority
and may delay entry into the IRQ handling routine for an
arbitrary length of time. This time can be reduced to 42 cycles if
the LDM command is not used. Some compilers have an option
to compile without using this command. Another option is to run
the part in thumb mode where the time is reduced to 22 cycles.
The minimum latency for FIQ or IRQ interrupts is a total of
five cycles, which consist of the shortest time the request can
take through the synchronizer plus the time to enter the
exception mode.
Note that the ARM7TDMI always runs in ARM (32-bit) mode
when in privileged modes, for example, when executing
interrupt service routines.
相關PDF資料
PDF描述
HBM10DSEI-S13 CONN EDGECARD 20POS .156 EXTEND
EBC35DCSD-S288 CONN EDGECARD 70POS .100 EXTEND
HBM15DRYN-S13 CONN EDGECARD 30POS .156 EXTEND
RBC17DRES-S13 CONN EDGECARD 34POS .100 EXTEND
HBM15DRYH-S13 CONN EDGECARD 30POS .156 EXTEND
相關代理商/技術參數
參數描述
USB-I2C-SS 功能描述:USB 接口集成電路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
USB-ICP-80C51ISP 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC2K 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC9XX 功能描述:程序設計器 - 基于處理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-SAB9 功能描述:插座和適配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x