參數資料
型號： USB-I2C/LIN-CONV-Z
廠商： Analog Devices Inc
文件頁數： 64/104頁
文件大小： 0K
描述： USB TO I2C/LIN CONV BOARD
標準包裝： 1
附件類型： 適配器板
適用于相關產品： ARM7TDMI?
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 62 of 104
DESCRIPTION OF THE PWM BLOCK
A functional block diagram of the PWM controller is shown in
Figure 68. The generation of the six output PWM signals on
Pin PWM0H to Pin PWM2L is controlled by the following four
important blocks:
The 3-phase PWM timing unit. The core of the PWM
controller, this block generates three pairs of complemented
and dead-time-adjusted, center-based PWM signals. This
unit also generates the internal synchronization pulse,
PWMSYNC. It also controls whether the external PWMSYNC
pin is used.
The output control unit. This block can redirect the
outputs of the 3-phase timing unit for each channel to
either the high-side or low-side output. In addition, the
output control unit allows individual enabling/disabling
of each of the six PWM output signals.
The gate drive unit. This block can generate the high
frequency chopping and its subsequent mixing with the
PWM signals.
The PWM shutdown controller. This block controls the
PWM shutdown via the PWMTRIP pin and generates the
correct reset signal for the timing unit.
The PWM controller is driven by the ADuC7019/20/21/22/24/
25/26/27/28/29 core clock frequency and is capable of generating
two interrupts to the ARM core. One interrupt is generated on
the occurrence of a PWMSYNC pulse, and the other is
generated on the occurrence of any PWM shutdown action.
3-Phase Timing Unit
PWM Switching Frequency (PWMDAT0 MMR)
The PWM switching frequency is controlled by the PWM
period register, PWMDAT0. The fundamental timing unit
of the PWM controller is
tCORE = 1/fCORE
where fCORE is the core frequency of the MicroConverter.
Therefore, for a 41.78 MHz fCORE, the fundamental time increment
is 24 ns. The value written to the PWMDAT0 register is effectively
the number of fCORE clock increments in one-half a PWM
period. The required PWMDAT0 value is a function of the
desired PWM switching frequency (fPWN) and is given by
PWMDAT0 = fCORE/(2 × fPWM)
Therefore, the PWM switching period, tS, can be written as
tS = 2 × PWMDAT0 × tCORE
The largest value that can be written to the 16-bit PWMDAT0
MMR is 0xFFFF = 65,535, which corresponds to a minimum
PWM switching frequency of
fPWM(min) = 41.78 × 106/(2 × 65,535) = 318.75 Hz
Note that PWMDAT0 values of 0 and 1 are not defined and
should not be used.
PWM Switching Dead Time (PWMDAT1 MMR)
The second important parameter that must be set up in the initial
configuration of the PWM block is the switching dead time. This
is a short delay time introduced between turning off one PWM
signal (0H, for example) and turning on the complementary
signal (0L). This short time delay is introduced to permit the
power switch to be turned off (in this case, 0H) to completely
recover its blocking capability before the complementary switch is
turned on. This time delay prevents a potentially destructive
short-circuit condition from developing across the dc link
capacitor of a typical voltage source inverter.
The dead time is controlled by the 10-bit, read/write PWMDAT1
register. There is only one dead-time register that controls the dead
time inserted into all three pairs of PWM output signals. The dead
time, tD, is related to the value in the PWMDAT1 register by
tD = PWMDAT1 × 2 × tCORE
Therefore, a PWMDAT1 value of 0x00A (= 10), introduces
a 426 ns delay between the turn-off on any PWM signal (0H,
for example) and the turn-on of its complementary signal (0L).
The amount of the dead time can, therefore, be programmed in
increments of 2tCORE (or 49 ns for a 41.78 MHz core clock).
04955-
027
PWM0H
PWM0L
PWM1H
PWM1L
PWM2H
PWM2L
PWMCON
PWMDAT0
PWMDAT1
PWMDAT2
PWMCH0
PWMCH1
PWMCH2
CONFIGURATION
REGISTERS DUTY CYCLE
REGISTERS
3-PHASE
PWM TIMING
UNIT
PWMEN
OUTPUT
CONTROL
UNIT
PWM
SHUTDOWN
CONTROLLER
PWMCFG
GATE
DRIVE
UNIT
PWMSYNC
PWMTRIP
TO INTERRUPT
CONTROLLER
SYNC
CORE CLOCK
Figure 68. Overview of the PWM Controller
相關PDF資料
PDF描述
HBM10DSEI-S13 CONN EDGECARD 20POS .156 EXTEND
EBC35DCSD-S288 CONN EDGECARD 70POS .100 EXTEND
HBM15DRYN-S13 CONN EDGECARD 30POS .156 EXTEND
RBC17DRES-S13 CONN EDGECARD 34POS .100 EXTEND
HBM15DRYH-S13 CONN EDGECARD 30POS .156 EXTEND
相關代理商/技術參數
參數描述
USB-I2C-SS 功能描述:USB 接口集成電路 Driver-free USB to serl SPIslve intrfce RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
USB-ICP-80C51ISP 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP 80C51ISP RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC2K 功能描述:程序設計器 - 基于處理器 In-System Programmer for NXP ARM7 LPC2xxx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-LPC9XX 功能描述:程序設計器 - 基于處理器 In-Circuit Programer for NXP LPC9xx RoHS:否 制造商:Olimex Ltd. 產品:Programmers 工具用于評估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口類型:USB 工作電源電壓:1.8 V to 5.5 V
USB-ICP-SAB9 功能描述:插座和適配器 Socket Adapter Brd USB-ICP-LPC9xx Drvr RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*