- 您現在的位置：買賣IC網 > PDF目錄2016 > SI3200-BS (Silicon Laboratories Inc)IC LINEFEED INTRFC 100V 16SOIC PDF資料下載
參數資料
| 型號： | SI3200-BS |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 77/128頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINEFEED INTRFC 100V 16SOIC |
| 標準包裝： | 48 |
| 系列： | ProSLIC® |
| 功能： | 用戶線路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 電路數： | 2 |
| 電源電壓： | 3.3V，5V |
| 電流 - 電源： | 110µA |
| 功率（瓦特）： | 941mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 管件 |
| 包括： | 電池切換，BORSCHT 功能，DTMF 生成和解碼，F(xiàn)SK 音調生成，調制解調器和傳真音調檢測 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Si3232
52
Preliminary Rev. 0.96
Not
Recommended
fo
r N
ew
D
esi
gn
s
4.17. Si3232 RAM and Register Space
The
Si3232
is
a
highly-programmable
telephone
linecard solution that uses internal registers and RAM to
program operational parameters and modes. The
Register Summary and RAM Summary are compressed
listings for single-entry quick reference. The Register
Descriptions and RAM Descriptions give detailed
information of each register or RAM location’s bits.
All RAM locations are cleared upon a hardware reset.
All RAM locations that are listed as “INIT” must be
initialized to a meaningful value for proper functionality.
Bit 4 of the MSTRSTAT register indicates the clearing
process is finished. This bit should be checked before
initializing the RAM space.
Accessing register and RAM space is performed
through the SPI. Register space is accessed by using
the standard three-byte access as described in the next
section. Bit 5 of the control byte specifies register
access when set to a 1. All register space is comprised
of 8-bit data.
4.17.1. RAM Access by Pipeline
Ram space can be accessed by two different methods.
One method is a pipeline method that employs a 4-byte
access plus a RAM status check. The control byte for
the pipeline method has bit 6 cleared to 0 to indicate a
RAM access. The control byte is followed by the RAM
address byte, then the two data bytes.
Reading RAM in the pipeline method requires “priming”
the data. First, check for register RAMSTAT, bit 0, to
indicate the previous access is complete and RAM is
ready (0). Then, perform the 4-byte RAM access. The
first read will yield unusable data. The data read on the
subsequent read access is the data for the previous
address read. A final address read yields the last
previously-requested data. The RAM-ready information
(RAMSTAT) must be read before every RAM access.
To write a RAM location, check for register RAMSTAT,
bit 0, to indicate the previous access is complete and
RAM is ready (0). Then, write the RAM address and
data in the 4-byte method. A write to RAM location
requires “priming” the data with subsequent accesses.
4.17.2. RAM Access by Register
An alternative method to access RAM space utilizes
three registers in sequence and monitors RAMSTAT
register, bit 0. These three registers are RAMADDR,
RAMDATLO, and RAMDATHI.
To read a RAM location in the Si3232, check for register
RAMSTAT (bit 0) to indicate the previous access is
complete and RAM is ready (0). Then, write the RAM
address to RAMADDR. Wait until RAMSTAT (bit 0) is a
1; then, the 16 bits of data can be read from the
RAMDATLO and RAMDATHI registers.
To write a RAM location in the Si3232, check for register
RAMSTAT (bit 0) to indicate the previous access is
completed and RAM is ready (0); then, write the 16 bits
of RAM data to the RAMDATLO, RAMDATHI. Finally,
write the RAM address to the RAMADDR register.
4.17.3. Chip Select
For register or RAM space access, there are three ways
to use chip select: byte length, 16-bit length, and access
duration length. The byte length method releases chip
select after every 8 bits of communication with the
Si3232. The time between chip select assertions must
be at least 220 ns.
The 16-bit length chip select method is similar to the
byte
length
method
except
that
16-bits
are
communicated with the Si3232. This means that Si3232
communication consists of a control byte, address byte
for one 16-bit access, and two data bytes for a second
16-bit access.
In a single data byte communication (control byte,
address byte, data byte), the data byte should be
loaded into either the high byte or both bytes of the
second 16-bit access for a write. The 8-bit data exists in
the high and low byte of a 16-bit access for a read. The
time between chip select assertion must be at least
220 ns.
Access duration length allows chip select to be pulled
low for the length of a number of Si3232 accesses.
There are two very specific rules for this type of
communication. One rule is that the SCLK must be of a
frequency that is less than 1/2x220 ns (<2.25 MHz).
The second rule is that access must be done in a 16-bit
modulus. This 16-bit modulus follows the same rules as
described above for 16-bit length access where 8-bit
data is concerned.
4.17.4. Protected Register Bits
The Si3232 has protected register bits that are meant to
retain the integrity of the Si3232 circuit in the event of
unintentional software register access. To access the
user-protected bits, write the following sequence of data
bytes to register address 87 (0x57):
0x02
0x10
0x12
0x00
Following the modification of any protected bit, the
same sequence should be immediately written to place
these bits into their protected state.
Protected bits exist in registers SBIAS and THERM.
相關PDF資料 |
PDF描述 |
|---|---|
| SI3211-KT | IC SLIC/CODEC PROG 1CH 38TSSOP |
| SI3216-FT | IC SLIC/CODEC 1CH 38TSSOP |
| SI3225-G-GQ | IC PROSLIC/CODEC DUAL 64TQFP |
| SI3230-KT | IC SLIC PROG 1-CH 38TSSOP |
| SI5010-B-GM | IC CLOCK/DATA RECOVERY LP 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3200-BSR | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3200-FS | 功能描述:電信線路管理 IC 100 V Linefeed Interface IC unit RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3200-FSR | 制造商:Silicon Laboratories Inc 功能描述:SLIC 2CH 70DB 45MA 3.3V/5V 16SOIC EP - Tape and Reel |
| Si3200-G-FS | 功能描述:射頻無線雜項 100 V Linefeed Inter IC unit price RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI3200-G-FSR | 功能描述:電信線路管理 IC 100 V Linefeed Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。