- 您現在的位置：買賣IC網 > PDF目錄2016 > SI3200-BS (Silicon Laboratories Inc)IC LINEFEED INTRFC 100V 16SOIC PDF資料下載
參數資料
| 型號： | SI3200-BS |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 40/128頁 |
| 文件大小： | 0K |
| 描述： | IC LINEFEED INTRFC 100V 16SOIC |
| 標準包裝： | 48 |
| 系列： | ProSLIC® |
| 功能： | 用戶線路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 電路數： | 2 |
| 電源電壓： | 3.3V，5V |
| 電流 - 電源： | 110µA |
| 功率（瓦特）： | 941mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 管件 |
| 包括： | 電池切換，BORSCHT 功能，DTMF 生成和解碼，F(xiàn)SK 音調生成，調制解調器和傳真音調檢測 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Si3232
Preliminary Rev. 0.96
19
Not
Recommended
fo
r N
ew
D
esi
gn
4. Functional Description
The Si3232 dual SLIC is a low-voltage CMOS device
that provides a fully-programmable SLIC with line
monitoring and test functions to create a dual-channel
analog
telephone
interface.
Intended
for
multiple
channel
applications,
the
Si3232
provides
high
integration and low-power operation for applications,
such as integrated access devices (IADs), voice-over
DSL systems, cable telephony systems, and voice-over
IP systems. These devices meet all relevant Bellcore
LSSGR, ITU, and ETSI standards.
The Si3232 performs the battery, overvoltage, ringing,
supervision, hybrid, and test functions on-chip in a low-
power,
small-footprint
solution.
All
high-voltage
functions are implemented using the Si3200 linefeed
interface IC allowing a highly-integrated solution that
offers the lowest total system cost.
The internal linefeed circuitry provides programmable
on-hook voltage and off-hook loop current, reverse
battery operation, loop or ground start operation, and
on-hook transmission. Loop current and voltage are
continuously
monitored
using
an
integrated
8-bit
monitor A/D converter. The Si3232 provides on-chip,
balanced,
5 REN
ringing
with
or
without
a
programmable dc offset eliminating the need for an
external bulk ring generator and per-channel ringing
relay typically used in unbalanced ringing applications.
Both sinusoidal and trapezoidal ringing waveshapes are
available. Ringing parameters, such as frequency,
waveshape, cadence, and offset, can be programmed
into registers to reduce external controller requirements.
All ringing options are software-programmable over a
wide range of parameters to address a wide variety of
application requirements.
The Si3232 also provides a variety of line monitoring
and subscriber loop testing. It has the ability to
continuously monitor and store all line voltage and
current parameters for fault detection, and all values are
available in registers for later use. In addition, the
Si3232
provides
line
card
and
subscriber
loop
diagnostic functions to eliminate the need for system-
level test equipment. These test and diagnostic
functions are intended to comply with relevant LSSGR
and ITU requirements for line-fault detection and
reporting, and all measured values are stored in
registers for later use or further calculations.
The Si3232 is software-programmable allowing a single
hardware design to meet international requirements.
Programmability is supported using a standard 4-wire
serial peripheral interface (SPI). The Si3232 is available
in a 64-lead thin quad flat package (TQFP), and the
Si3200 is available in a thermally-enhanced 16-lead
SOIC.
4.1. Linefeed Architecture
The Si3232 is a low-voltage CMOS device that uses a
low-cost integrated linefeed interface IC to control the
high voltages required for subscriber line interfaces.
Figure 6 is a simplified single-ended model of the
linefeed control loop circuit for both the TIP and RING
leads.
The Si3232 uses both voltage and current sensing to
control TIP and RING. DC line voltages on TIP and
RING are measured through sense resistors RDC. AC
line voltages on TIP and RING are measured through
sense resistors RAC. The Si3232 uses the Si3200
linefeed interface to drive TIP and RING.
The Si3232 measures voltage at various nodes to
monitor the linefeed current. RDC and RBAT provide
access to these measuring points. The sense circuitry is
calibrated on-chip to guarantee measurement accuracy.
See "4.4. Linefeed Calibration" on page 25 for details on
linefeed calibration.
4.2. Power Supply Transients on the
Si3200
The Si3200 features an ESD clamp protection circuit
connected between the VDD and VBATH rails. This
clamp protects the Si3200 against ESD damage when
the device is being handled out-of-circuit during
manufacture. Precautions must be taken in the VDD and
VBATH system power supply design. At power-up, the
VDD and VBATH rails must ramp-up from 0 V to their
respective target values in a linear fashion and must not
exhibit fast transients or oscillations which could cause
the ESD clamp to be activated for an extended period of
time resulting in damage to the Si3200. The resistors
shown as R20 through R23 together with capacitors
C23, C24, C30 and C31 in the Application Schematic
on page 17) provide some measure of
protection against in-circuit ESD clamp activation by
forming a filter time constant and by providing current
limitting action in case of momentary clamp activation
during power-up. These resistors and capacitors must
be included in the application circuit, while ensuring that
the VDD and VBATH system power supplies are
designed to exhibit start-up behavior that is free of
undesirable transients or oscillations. Once the VDD and
VBATH are in their steady state final values, the ESD
clamp has circuitry that prevents it from being activated
by transients slower than 10 V/us. In the steady
powered-up state, the VDD and VBATH rails must
therefore not exhibit transients resulting in a voltage
slew rate greater than 10 V/s.
相關PDF資料 |
PDF描述 |
|---|---|
| SI3211-KT | IC SLIC/CODEC PROG 1CH 38TSSOP |
| SI3216-FT | IC SLIC/CODEC 1CH 38TSSOP |
| SI3225-G-GQ | IC PROSLIC/CODEC DUAL 64TQFP |
| SI3230-KT | IC SLIC PROG 1-CH 38TSSOP |
| SI5010-B-GM | IC CLOCK/DATA RECOVERY LP 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3200-BSR | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3200-FS | 功能描述:電信線路管理 IC 100 V Linefeed Interface IC unit RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3200-FSR | 制造商:Silicon Laboratories Inc 功能描述:SLIC 2CH 70DB 45MA 3.3V/5V 16SOIC EP - Tape and Reel |
| Si3200-G-FS | 功能描述:射頻無線雜項 100 V Linefeed Inter IC unit price RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI3200-G-FSR | 功能描述:電信線路管理 IC 100 V Linefeed Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。