- 您現在的位置：買賣IC網 > PDF目錄372063 > RJ80530MY650256 MICROPROCESSOR|32-BIT|CMOS|BGA|479PIN|CERAMIC PDF資料下載
參數資料
| 型號： | RJ80530MY650256 |
| 元件分類： | 微處理器 |
| 英文描述： | MICROPROCESSOR|32-BIT|CMOS|BGA|479PIN|CERAMIC |
| 中文描述： | 微處理器| 32位|的CMOS | BGA封裝| 479PIN |陶瓷 |
| 文件頁數： | 84/89頁 |
| 文件大小： | 1672K |
| 代理商： | RJ80530MY650256 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁
Mobile Intel
Pentium
III Processor-M Datasheet
84
Datasheet
298340-002
TESTLO[2:1] (I - 1.5V Tolerant)
The TESTLO[2:1] (Test input Low) signals are used during processor test and needs to be pulled to
ground during normal operation.
THERMDA, THERMDC (Analog)
The THERMDA (Thermal Diode Anode) and THERMDC (Thermal Diode Cathode) signals connect
to the anode and cathode of the on-die thermal diode.
TMS (I - 1.5V Tolerant)
The TMS (Test Mode Select) signal is a JTAG support signal used by debug tools.
TRDY# (I/O - AGTL)
The TRDY# (Target Ready) signal is asserted by the target to indicate that the target is ready to receive
write or implicit write-back data transfer. TRDY# must be connected to the appropriate pins/balls on
both agents on the system bus.
TRST# (I - 1.5V Tolerant)
The TRST# (Test Reset) signal resets the Test Access Port (TAP) logic. The Mobile Intel Pentium
III
Processor-Ms do not self-reset during power on; therefore, it is necessary to drive this signal low
during power-on reset.
VID[4:0] (O – Open-drain)
The VID[4:0] (Voltage ID) pins/balls can be used to support automatic selection of power supply
voltages. Please refer to Section 3.2.2 for details.
VREF (Analog)
The VREF (AGTL Reference Voltage) signal provides a DC level reference voltage for the AGTL
input buffers. A voltage divider should be used to divide V
CCT
by
2
/
3
. Resistor values of 1.00 k
and
2.00 k
are recommended. Decouple the VREF signal with three 0.1-
μ
F high-frequency capacitors
close to the processor.
VTTPWRGD (I – 1.25V)
The VTTPWRGD signal informs the processor to output the VID signals. During power up, the VID
signals will be in an indeterminate state for a small period of time. The voltage regulator should not
sample and/or latch the VID signals until the VTTPWRGD signal is asserted. The assertion of the
VTTPWRGD signal indicates that the VID signals are stable and are driven to the final state by the
processor. Please refer to Figure 12 for the power up sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| RJ80530NZ001256 | Microprocessor |
| RJ80530VY700256 | Microprocessor |
| RJ80530VZ733256 | Microprocessor |
| RHFL4913 | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| RHFL4913S50-04V | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RJ80530MZ001256 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述: |
| RJ80530MZ001256S L798 | 制造商:Intel 功能描述:32BIT MPU 80530MZ001256 1.00G |
| RJ80530MZ733256 | 制造商:Rochester Electronics LLC 功能描述:MOBILE CELERON 733MHZ, 256K - Bulk |
| RJ80530MZ733256S L6B4 | 制造商:Intel 功能描述:MPU Celeron 制造商:Intel 功能描述:MPU Celeron? Processor 64-Bit 0.13um 733MHz 478-Pin uFCPGA |
| RJ80530MZ866256 | 制造商:Rochester Electronics LLC 功能描述:32BIT MPU - Bulk 制造商:Intel 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。