- 您現在的位置：買賣IC網 > PDF目錄367854 > PDI1394P24 (NXP Semiconductors N.V.) 2-port 400 Mbps physical layer interface(2端口 400 Mbps物理層接口) PDF資料下載
參數資料
| 型號： | PDI1394P24 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2-port 400 Mbps physical layer interface(2端口 400 Mbps物理層接口) |
| 中文描述： | 2端口400 Mbps的物理層接口（2端口400 Mbps的物理層接口） |
| 文件頁數： | 35/39頁 |
| 文件大?。?/td> | 188K |
| 代理商： | PDI1394P24 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁
Philips Semiconductors
Objective specification
PDI1394P24
2-port 400 Mbps physical layer interface
2000 Jun 23
35
The sequence of events for initialization of the PHY–LLC interface
when the interface is in the differentiated mode of operation (ISO
terminal is low) is as follows:
1. LPS reasserted. After the interface has been in the reset or
disabled state for at least the minimum T
RESTORE
time, the LLC
causes the interface to be initialized and restored to normal
operation by re–activating the LPS signal. (In the above diagram,
the interface is shown in the disabled state with SYSCLK
high–impedance inactive. However, the interface initialization
sequence described here is also executed if the interface is
merely reset but not yet disabled.)
2. SYSCLK activated. If the interface is disabled, the PHY
re–activates its SYSCLK output when it detects that LPS has
been reasserted. If the PHY has entered a low–power state, it
will take between 5.3 to 7.3 ms for SYSCLK to be restored; if the
PHY is not in a low–power state, SYSCLK will be restored within
60 ns. The PHY commences SYSCLK activity by driving the
SYSCLK output low for half a cycle. Thereafter, the SYSCLK
output is a 50% duty cycle square wave with a frequency of
49.152 MHz +100 ppm (period of 20.345 ns). Upon the first full
cycle of SYSCLK, the PHY drives the CTL and D terminals low
for one cycle. The LLC is also required to drive its CTL, D, and
LREQ outputs low during one of the first six cycles of SYSCLK
(in the above diagram, this is shown as occurring in the first
SYSCLK cycle).
3. Receive indicated. Upon the eighth SYSCLK cycle following
reassertion of LPS, the PHY asserts the Receive state on the
CTL lines and the data–on indication (all ones) on the D lines for
one or more cycles (because the interface is in the differentiated
mode of operation, the CTL and D lines will be in the
high–impedance state after the first cycle).
4. Initialization complete. The PHY asserts the Idle state on the
CTL lines and logic 0 on the D lines. This indicates that the
PHY–LLC interface initialization is complete and normal
operation may commence. The PHY will now accept requests
from the LLC via the LREQ line.
T
CLK_ACTIVATE
CTL0
LPS
SV01815
ISO
SYSCLK
D0 – D7
LREQ
(high)
(c)
7 cycles
(b)
CTL1
(a)
Figure 24.
Interface Initialization, ISO High
The sequence of events for initialization of the PHY–LLC interface
when the interface is in the non–differentiated mode of operation
(ISO terminal is high) is as follows:
1. LPS reasserted. After the interface has been in the reset or
disabled state for at least the minimum T
RESTORE
time, the LLC
causes the interface to be initialized and restored to normal
operation by reasserting the LPS signal. (In the above diagram,
the interface is shown in the disabled state with SYSCLK low
inactive. However, the interface initialization sequence described
here is also executed if the interface is merely reset but not yet
disabled.)
2. SYSCLK activated. If the interface is disabled, the PHY
re–activates its SYSCLK output when it detects that LPS has
been reasserted. If the PHY has entered a low–power state, it
will take between 5.3 to 7.3 ms for SYSCLK to be restored; if the
PHY is not in a low–power state, SYSCLK will be restored within
60 ns. The SYSCLK output is a 50% duty cycle square wave
with a frequency of 49.152 MHz +100 ppm (period of 20.345 ns).
During the first seven cycles of SYSCLK, the PHY continues to
drive the CTL and D terminals low. The LLC is also required to
drive its CTL and D outputs low for one of the first six cycles of
SYSCLK but to otherwise place its CTL and D outputs in a
high–impedance state. The LLC continues to drive its LREQ
output low during this time.
3. Receive indicated. Upon the eighth SYSCLK cycle following
reassertion of LPS, the PHY asserts the Receive state on the
相關PDF資料 |
PDF描述 |
|---|---|
| PDI40C1D00 | |
| PDI40C1300 | |
| PDI40C130R | |
| PDI40C130X | |
| PDI40C13R0 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394P24BD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINE TRANSCEIVER|CMOS|4 DRIVER|4 RCVR|QFP|64PIN|PLASTIC |
| PDI1394P25 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1-port 400 Mbps physical layer interface |
| PDI1394P25BD | 功能描述:輸入/輸出控制器接口集成電路 1394 1 PORT 400 MB/S PHY RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| PDI1394P25BD,118 | 制造商:NXP Semiconductors 功能描述:1394 1 PORT 400 MB/S PHY - Tape and Reel |
| PDI1394P25BD,151 | 制造商:NXP Semiconductors 功能描述:1394 1 PORT 400 MB/S PHY - Trays |
發布緊急采購，3分鐘左右您將得到回復。