- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6004AFTBR2G (ON Semiconductor)IC INTERFACE SAM/SIM DUAL 48TQFP PDF資料下載
參數資料
| 型號： | NCN6004AFTBR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 40/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE SAM/SIM DUAL 48TQFP |
| 標準包裝： | 1 |
| 應用： | PC，PDA |
| 接口： | 微控制器 |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6004AFTBR2GOSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁
NCN6004A
http://onsemi.com
9
PIN DESCRIPTION (continued)
Pin
Description
Type
Symbol
47
INT
OUTPUT
This pin is activated LOW when a card has been inserted and detected in either of the
external ports. The signal is reset by either a positive going transition on pin CS, or by a
High level on pin PWR_ON combined with CS = Low.
Similarly, an interrupt is generated when either one of the CRD_VCC output is overloaded.
On the other hand, the pin is forced to a logic High when the input voltage VCC drops
below 2.0 V min.
The associated pull up resistor is either connected to VCC (EN_RPU = H) or
disconnected when EN_RPU = Low.
48
ANLG_GND
GROUND
This pin is the ground reference for both analog and digital signals and must be
connected to the system Ground. Care must be observed to provide a copper PCB layout
designed to avoid small signals and power transients sharing the same track. Good high
frequency techniques are strongly recommended.
MAXIMUM RATINGS (Note 2)
Rating
Symbol
Value
Unit
Power Supply Input Supply Voltage
VCC
6
V
Vin
Digital Input Pins
0.5 V < Vin< VCC +0.5 V,
but < 6.0 V
V
Power Supply Input Current
IVCC
500
mA
Digital Input Pins
Vin
In
0.5 < VCC or VCC < 5.5
" 5
V
mA
Digital Output Pins
Vout
Iout
0.5 < VCC or VCC < 5.5
"10
V
mA
Card Interface Pins
Vcard
Icard
0.5V < Vcard < CRD_VCC +0.5V
15 mA (internally limited)
V
mA
ESD Capability, Human Body Model (Note 3)
Standard Pins
Card Interface Pins (Card A or B)
VESD
2
8
kV
TQFP48
Power Dissipation @ Tab = +85
°C
Thermal Resistance JunctiontoAir
PD
RJqA
800
50
mW
°C/W
Operating Ambient Temperature Range
TA
40 to +85
°C
Operating Junction Temperature Range
TJ
40 to +125
°C
Maximum Junction Temperature (Note 4)
TJmax
+150
°C
Storage Temperature Range
Tag
65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
2. Maximum Electrical Ratings are defined as those values beyond which damage(s) to the device may occur at TA = +25°C.
3. Human Body Model, R = 1500
W, C = 100 pF.
4. Absolute Maximum Rating beyond which damage(s) to the device may occur.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
| NCN8025MTTBG | IC SMART CARD I2C 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6010 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SIM Card Supply and Level Shifter |
| NCN6010DTB | 功能描述:轉換 - 電壓電平 2.7V Sim Card RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。