- 您現在的位置：買賣IC網 > PDF目錄384544 > ISPCLOCK5600 (Lattice Semiconductor Corporation) In-System Programmable, Zero-Delay Clock Generator with Universal Fan-Out Buffer PDF資料下載
參數資料
| 型號： | ISPCLOCK5600 |
| 廠商： | Lattice Semiconductor Corporation |
| 英文描述： | In-System Programmable, Zero-Delay Clock Generator with Universal Fan-Out Buffer |
| 中文描述： | 在系統可編程，零延遲時鐘發生器通用扇出緩沖器 |
| 文件頁數： | 35/47頁 |
| 文件大小： | 871K |
| 代理商： | ISPCLOCK5600 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Lattice Semiconductor
ispClock5600 Family Data Sheet
35
Test/Idle, Shift-Data-Register, Pause-Data-Register, Shift-Instruction-Register and Pause-Instruction-Register. But
there is only one steady state for the condition when TMS is set high: the Test-Logic-Reset state. This allows a
reset of the test logic within
fi
ve TCKs or less by keeping the TMS input high. Test-Logic-Reset is the power-on
default state.
Figure 31. TAP States
When the correct logic sequence is applied to the TMS and TCK inputs, the TAP will exit the Test-Logic-Reset state
and move to the desired state. The next state after Test-Logic-Reset is Run-Test/Idle. Until a data or instruction shift
is performed, no action will occur in Run-Test/Idle (steady state = idle). After Run-Test/Idle, either a data or instruc-
tion shift is performed. The states of the Data and Instruction Register blocks are identical to each other differing
only in their entry points. When either block is entered, the
fi
rst action is a capture operation. For the Data Regis-
ters, the Capture-DR state is very simple: it captures (parallel loads) data onto the selected serial data path (previ-
ously chosen with the appropriate instruction). For the Instruction Register, the Capture-IR state will always load
the IDCODE instruction. It will always enable the ID Register for readout if no other instruction is loaded prior to a
Shift-DR operation. This, in conjunction with mandated bit codes, allows a “blind” interrogation of any device in a
compliant IEEE 1149.1 serial chain. From the Capture state, the TAP transitions to either the Shift or Exit1 state.
Normally the Shift state follows the Capture state so that test data or status information can be shifted out or new
data shifted in. Following the Shift state, the TAP either returns to the Run-Test/Idle state via the Exit1 and Update
states or enters the Pause state via Exit1. The Pause state is used to temporarily suspend the shifting of data
through either the Data or Instruction Register while an external operation is performed. From the Pause state,
shifting can resume by reentering the Shift state via the Exit2 state or be terminated by entering the Run-Test/Idle
state via the Exit2 and Update states. If the proper instruction is shifted in during a Shift-IR operation, the next entry
into Run-Test/Idle initiates the test mode (steady state = test). This is when the device is actually programmed,
erased or veri
fi
ed. All other instructions are executed in the Update state.
Test Instructions
Like data registers, the IEEE 1149.1 standard also mandates the inclusion of certain instructions. It outlines the
function of three required and six optional instructions. Any additional instructions are left exclusively for the manu-
Test-Logic-Rst
Run-Test/Idle
Select-DR-Scan
Select-IR-Scan
Capture-DR
Capture-IR
Shift-DR
Shift-IR
Exit1-DR
Exit1-IR
Pause-DR
Pause-IR
Exit2-DR
Exit2-IR
Update-DR
Update-IR
1
0
0
0
0
0
0
0
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
1
1
1
1
1
0
Note: The value shown adjacent to each state transition in this figure
represents the signal present at TMS at the time of a rising edge at TCK.
相關PDF資料 |
PDF描述 |
|---|---|
| ISPPAC-CLK5610V-01T100C | In-System Programmable, Zero-Delay Clock Generator with Universal Fan-Out Buffer |
| ISPPAC-CLK5620V-01T100C | LED Area Light; LED Color:Blue; Leaded Process Compatible:No; Light Emitting Area:80x80mm; Peak Reflow Compatible (260 C):No; Supply Current:250mA; Supply Voltage:24VDC; Wavelength:470nm |
| ISPPAC-CLK5620V-01T100I | In-System Programmable, Zero-Delay Clock Generator with Universal Fan-Out Buffer |
| ISPPAC-CLK5610V-01T48C | Spot Light; LED Color:Blue; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No; Supply Current:160mA; Supply Voltage:30VDC; Wavelength:470nm |
| ISPPAC-CLK5620V-01T48C | LED Area Light; LED Color:Green; Leaded Process Compatible:No; Light Emitting Area:62x62mm; Peak Reflow Compatible (260 C):No; Supply Current:200mA; Supply Voltage:24VDC; Wavelength:525nm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISPCLOCK5600A | 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:In-System Programmable, Enhanced Zero-Delay, Clock Generator with Universal Fan-Out Buffer |
| ISPCLOCK5610A | 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:In-System Programmable, Enhanced Zero-Delay, Clock Generator with Universal Fan-Out Buffer |
| ISPCLOCK5620A | 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:In-System Programmable, Enhanced Zero-Delay, Clock Generator with Universal Fan-Out Buffer |
| ISPD60 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DARLINGTON-NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| ISPD60_10 | 制造商:ISOCOM 制造商全稱:ISOCOM 功能描述:NON BASE LEAD OPTICALLY COUPLED ISOLATOR PHOTODARLINGTON OUTPUT |
發布緊急采購，3分鐘左右您將得到回復。