- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1161BM (NXP SEMICONDUCTORS) Full-speed Universal Serial Bus single-chip host and device controller PDF資料下載
參數資料
| 型號： | ISP1161BM |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Full-speed Universal Serial Bus single-chip host and device controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-414-1, LQFP-64 |
| 文件頁數： | 50/127頁 |
| 文件大小： | 2762K |
| 代理商： | ISP1161BM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
50 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
The following example shows the steps which occur in a typical DMA transfer:
1. ISP1161 DC receives a data packet in one of its endpoint FIFOs; the packet must
be transferred to memory address 1234H.
2. ISP1161 DC asserts the DREQ2 signal requesting the 8237 for a DMA transfer.
3. The 8237 asks the CPU to release the bus by asserting the HRQ signal.
4. After completing the current instruction cycle, the CPU places the bus control
signals (MEMR, MEMW, IOR and IOW) and the address lines in three-state and
asserts HLDA to inform the 8237 that it has control of the bus.
5. The 8237 now sets its address lines to 1234H and activates the MEMW and IOR
control signals.
6. The 8237 asserts DACK to inform the ISP1161 DC that it will start a DMA
transfer.
7. The ISP1161 DC now places the word to be transferred on the data bus lines,
because its RD signal was asserted by the 8237.
8. The 8237 waits one DMA clock period and then de-asserts MEMW and IOR. This
latches and stores the word at the desired memory location. It also informs the
ISP1161 DC that the data on the bus lines has been transferred.
9. The ISP1161 DC de-asserts the DREQ2 signal to indicate to the 8237 that DMA
is no longer needed. In
Single cycle mode
this is done after each word, in
Burst
mode
following the last transferred word of the DMA cycle.
10. The 8237 de-asserts the DACK output indicating that the ISP1161 must stop
placing data on the bus.
11. The 8237 places the bus control signals (MEMR, MEMW, IOR and IOW) and the
address lines in three-state and de-asserts the HRQ signal, informing the CPU
that it has released the bus.
12. The CPU acknowledges control of the bus by de-asserting HLDA. After activating
the bus control lines (MEMR, MEMW, IOR and IOW) and the address lines, the
CPU resumes the execution of instructions.
For a typical bulk transfer the above process is repeated, once for each byte. After
each byte the address register in the DMA controller is incremented and the byte
counter is decremented. When using 16-bit DMA the number of transfers is 32 and
address incrementing and byte counter decrementing is done by 2 for each word.
12.3 DACK-only mode
The DACK-only DMA mode is selected by setting bit DAKOLY in the Hardware
Configuration Register (see
Table 81
). The pin functions for this mode are shown in
Table 12
. A typical example of ISP1161 DC in DACK-only DMA mode is given in
Figure 39
.
Table 12: DACK-only mode: pin functions
Symbol
Description
DREQ2
DC’s DMA request
DACK2
DC’s DMA
acknowledge
I/O
O
I
Function
ISP1161 DC requests a DMA transfer
DMA controller confirms the transfer;
also functions as data strobe
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181ABS | INDUCTOR 1.0NH +-.3NH FIXED SMD |
| ISP1181A | Full-speed Universal Serial Bus peripheral controller |
| ISP1181ADGG | Full-speed Universal Serial Bus peripheral controller |
| ISP1181B | Full-speed Universal Serial Bus peripheral controller |
| ISP1181BBS | Full-speed Universal Serial Bus peripheral controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus interface device |
| ISP1181A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller |
| ISP1181ABS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller |
| ISP1181ABS,518 | 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181ABS,551 | 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。