參數資料
型號： ISP1161BM
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Full-speed Universal Serial Bus single-chip host and device controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-414-1, LQFP-64
文件頁數： 31/127頁
文件大?。?/td> 2762K
代理商： ISP1161BM
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
31 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
Following is an example of a C program that shows how to write data into the ATL
buffer RAM. The total number of data bytes to be transferred is 80 (decimal) which
will be set into the HcTransferCounter register as 50H. The data consists of four types
of PTD data:
1. The first PTD header (IN) is 8 bytes, followed by 16 bytes of space reserved for its
payload data;
2. The second PTD header (IN) is also 8 bytes, followed by 8 bytes of space
reserved for its payload data;
3. The third PTD header (OUT) is 8 bytes, followed by 16 bytes of payload data with
values beginning from 0H to FH incrementing by 1;
4. The fourth PTD header (OUT) is also 8 bytes, followed by 8 bytes of payload data
with values beginning from 0H to EH incrementing by 2.
In all PTD’s, we assign device address 5 and endpoint 1. ActualBytes is always zero
(0). TotalBytes equals the number of payload data bytes. The following table shows
the results after running this program.
However, if communication with a peripheral USB device is desired, the device should
be connected to the downstream port and pass enumeration.
//The example program for writing ATL buffer RAM
#include <conio.h>
#include <stdio.h>
#include <dos.h>
//Define register commands
#define wHcTransferCounter 0x22
#define wHcuPInterrupt 0x24
#define wHcATLBufferLength 0x2b
#define wHcBufferStatus 0x2c
// Define I/O Port Address for HC
#define HcDataPort 0x290
#define HcCmdPort 0x292
//Declare external functions to be used
unsigned int HcRegRead(unsigned int wIndex);
void HcRegWrite(unsigned int wIndex,unsigned int wValue);
void main(void)
{
Table 6:
Observed items
Run results of the C program example
HC not initialized and not
under Operational state
HC initialized and under
Operational state
Comments
Hc
μ
Pinterrupt Register
Bit 1 (ATLInt)
Bit 2 (AllEOTInterrupt)
HcBufferStatus Register
Bit 2 (ATLBufferFull)
Bit 5 (ATLBufferDone)
USB Traffic on USB Bus
0
1
1
1
microprocessor must read ATL
transfer completed
1
0
1
1
transfer completed
PTD data processed by HC
OUT packets can be seen
No
Yes
相關PDF資料
PDF描述
ISP1181ABS INDUCTOR 1.0NH +-.3NH FIXED SMD
ISP1181A Full-speed Universal Serial Bus peripheral controller
ISP1181ADGG Full-speed Universal Serial Bus peripheral controller
ISP1181B Full-speed Universal Serial Bus peripheral controller
ISP1181BBS Full-speed Universal Serial Bus peripheral controller
相關代理商/技術參數
參數描述
ISP1181 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus interface device
ISP1181A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller
ISP1181ABS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller
ISP1181ABS,518 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABS,551 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*