參數資料
型號: ADUC812BSZ-REEL
廠商: Analog Devices Inc
文件頁數: 56/57頁
文件大小: 0K
描述: IC MCU FLASH 12BIT ADC 52MQFP
標準包裝: 800
系列: MicroConverter® ADuC8xx
核心處理器: 8052
芯體尺寸: 8-位
速度: 16MHz
連通性: I²C,SPI,UART/USART
外圍設備: PSM,溫度傳感器,WDT
輸入/輸出數: 34
程序存儲器容量: 8KB(8K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 640 x 8
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 8x12b,D/A 2x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 52-QFP
包裝: 帶卷 (TR)
REV.
ADuC812
–8–
Mnemonic
Type
Function
PSEN
O
Program Store Enable, Logic Output. This output is a control signal that enables the external program
memory to the bus during external fetch operations. It is active every six oscillator periods except during
external data memory accesses. This pin remains high during internal program execution.
PSEN can also be
used to enable serial download mode when pulled low through a resistor on power-up or RESET.
ALE
O
Address Latch Enable, Logic Output. This output is used to latch the low byte (and page byte for 24-bit
address space accesses) of the address into external memory during normal operation. It is activated every
six oscillator periods except during an external data memory access.
EA
I
External Access Enable, Logic Input. When held high, this input enables the device to fetch code from
internal program memory locations 0000H to 1FFFH. When held low, this input enables the device to fetch
all instructions from external program memory.
P0.7–P0.0
I/O
Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float and in
(A0–A7)
that state can be used as high impedance inputs. Port 0 is also the multiplexed low order address and data
bus during accesses to external program or data memory. In this application, it uses strong internal pull-ups
when emitting 1s.
TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity
This is the maximum deviation of any code from a straight line
passing through the endpoints of the ADC transfer function.
The endpoints of the transfer function are zero scale, a point
1/2 LSB below the first code transition, and full scale, a point
1/2 LSB above the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (0000 . . . 000)
to (0000 . . . 001) from the ideal, i.e., +1/2 LSB.
Full-Scale Error
This is the deviation of the last code transition from the ideal
AIN voltage (Full Scale – 1.5 LSB) after the offset error has
been adjusted out.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the fun-
damental. Noise is the rms sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent upon the number of quantization levels in the digiti-
zation process; the more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by:
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Thus for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion
Total Harmonic Distortion is the ratio of the rms sum of the
harmonics to the fundamental.
DAC SPECIFICATIONS
Relative Accuracy
Relative accuracy or endpoint linearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
adjusting for zero-scale error and full-scale error.
Voltage Output Settling Time
This is the amount of time it takes for the output to settle to a
specified level for a full-scale input change.
Digital-to-Analog Glitch Impulse
This is the amount of charge injected into the analog output
when the inputs change state. It is specified as the area of the
glitch in nV sec.
PIN FUNCTION DESCRIPTIONS (continued)
F
EP
Exposed Pad. For the LFCSP, the exposed pad must be soldered and left unconnected.
相關PDF資料
PDF描述
ADUC814BRU IC ADC 12BIT W/FLASH MCU 28TSSOP
ADUC816BCP IC MCU 8K FLASH ADC/DAC 56LFCSP
ADUC824BSZ-REEL IC MCU 8K FLASH ADC/DAC 52MQFP
ADUC831BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC832BSZ-REEL IC MCU 62K FLASH ADC/DAC 52MQFP
相關代理商/技術參數
參數描述
ADUC813BS 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C. - Trays
ADUC814 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU
ADUC814_02 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded FLASH MCU
ADUC814AN 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 16.78MHz 8KB (8K x 8) FLASH 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包裝:- 零件狀態:上次購買時間 核心處理器:8052 核心尺寸:8-位 速度:16.78MHz 連接性:I2C,SPI,UART/USART 外設:POR,PSM,溫度傳感器,WDT I/O 數:- 程序存儲容量:8KB(8K x 8) 程序存儲器類型:閃存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 電壓 - 電源(Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:* 振蕩器類型:內部 工作溫度:* 封裝/外殼:- 供應商器件封裝:- 標準包裝:1
ADUC814ARU 功能描述:IC ADC 12BIT W/FLASH MCU 28TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND