- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC812BSZ-REEL (Analog Devices Inc)IC MCU FLASH 12BIT ADC 52MQFP PDF資料下載
參數資料
| 型號： | ADUC812BSZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/57頁 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 12BIT ADC 52MQFP |
| 標準包裝： | 800 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 8x12b，D/A 2x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 52-QFP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
REV.
ADuC812
–29–
8051 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are fully 8051 compatible and are
controlled via standard 8051 SFR bit definitions.
Parallel I/O Ports 0–3
The ADuC812 uses four input/output ports to exchange data with
external devices. In addition to performing general-purpose I/O,
some ports are capable of external memory operations; others
are multiplexed with an alternate function for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0 is an 8-bit, open-drain, bidirectional I/O port that is directly
controlled via the P0 SFR (SFR address = 80H). Port 0 pins
that have 1s written to them via the Port 0 SFR will be configured
as open-drain and will therefore float. In that state, Port 0 pins can
be used as high impedance inputs. An external pull-up resistor
will be required on Port 0 outputs to force a valid logic high
level externally. Port 0 is also the multiplexed low order address
and data bus during accesses to external program or data memory.
In this application, it uses strong internal pull-ups when emitting 1s.
Port 1 is also an 8-bit port directly controlled via the P1 SFR
(SFR address = 90H). Port 1 is an input only port. Port 1 digital
output capability is not supported on this device. Port 1 pins can
be configured as digital inputs or analog inputs.
By (power-on) default these pins are configured as analog inputs,
i.e., “1” written in the corresponding Port 1 register bit. To
configure any of these pins as digital inputs, the user should write
a “0” to these port bits to configure the corresponding pin as a
high impedance digital input.
These pins also have various secondary functions described in
Table XIII.
Table XIII. Port 1, Alternate Pin Functions
Pin
Alternate Function
P1.0
T2 (Timer/Counter 2 External Input)
P1.1
T2EX (Timer/Counter 2 Capture/Reload Trigger)
P1.5
SS (Slave Select for the SPI Interface)
Port 2 is a bidirectional port with internal pull-up resistors directly
controlled via the P2 SFR (SFR address = A0H). Port 2 pins
that have 1s written to them are pulled high by the internal pull-up
resistors and, in that state, can be used as inputs. As inputs, Port
2 pins being pulled externally low will source current because of
the internal pull-up resistors. Port 2 emits the high order
address bytes during fetches from external program memory,
and middle and high order address bytes during accesses to the
24-bit external data memory space.
Port 3 is a bidirectional port with internal pull-ups directly
controlled via the P3 SFR (SFR address = B0H). Port 3 pins
that have 1s written to them are pulled high by the internal pull-ups
and, in that state, can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal
pull-ups. Port 3 pins also have various secondary functions
described in Table XIV.
Table XIV. Port 3, Alternate Pin Functions
Pin
Alternate Function
P3.0
RxD (UART Input Pin)
(or Serial Data I/O in Mode 0)
P3.1
TxD (UART Output Pin)
(or Serial Clock Output in Mode 0)
P3.2
INT0 (External Interrupt 0)
P3.3
INT1 (External Interrupt 1)
P3.4
T0 (Timer/Counter 0 External Input)
P3.5
T1 (Timer/Counter 1 External Input)
P3.6
WR (External Data Memory Write Strobe)
P3.7
RD (External Data Memory Read Strobe)
The alternate functions of P1.0, P1.1, P1.5, and Port 3 pins
can be activated only if the corresponding bit latch in the P1
and P3 SFRs contains a 1. Otherwise, the port pin is stuck at 0.
Timers/Counters
The ADuC812 has three 16-bit Timer/Counters: Timer 0,
Timer 1, and Timer 2. The Timer/Counter hardware has been
included on-chip to relieve the processor core of the overhead
inherent in implementing timer/counter functionality in software.
Each Timer/Counter consists of two 8-bit registers, THx and
TLx (x = 0, 1, and 2). All three can be configured to operate
either as timers or event counters.
In Timer function, the TLx register is incremented every machine
cycle. Thus, think of it as counting machine cycles. Since a
machine cycle consists of 12 core clock periods, the maximum
count rate is 1/12 of the core clock frequency.
In Counter function, the TLx register is incremented by a 1-to-0
transition at its corresponding external input pin, T0, T1, or T2.
In this function, the external input is sampled during S5P2 of
every machine cycle. When the samples show a high in one cycle and
a low in the next cycle, the count is incremented. The new count
value appears in the register during S3P1 of the cycle following the
one in which the transition was detected. Since it takes two machine
cycles (24 core clock periods) to recognize a 1-to-0 transition,
the maximum count rate is 1/24 of the core clock frequency.
There are no restrictions on the duty cycle of the external input
signal, but to ensure that a given level is sampled at least once
before it changes, it must be held for a minimum of one full
machine cycle.
F
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC814BRU | IC ADC 12BIT W/FLASH MCU 28TSSOP |
| ADUC816BCP | IC MCU 8K FLASH ADC/DAC 56LFCSP |
| ADUC824BSZ-REEL | IC MCU 8K FLASH ADC/DAC 52MQFP |
| ADUC831BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC813BS | 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C. - Trays |
| ADUC814 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU |
| ADUC814_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded FLASH MCU |
| ADUC814AN | 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 16.78MHz 8KB (8K x 8) FLASH 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包裝:- 零件狀態:上次購買時間 核心處理器:8052 核心尺寸:8-位 速度:16.78MHz 連接性:I2C，SPI，UART/USART 外設:POR，PSM，溫度傳感器，WDT I/O 數:- 程序存儲容量:8KB（8K x 8） 程序存儲器類型:閃存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 電壓 - 電源（Vcc/Vdd）:2.7 V ~ 5.5 V 數據轉換器:* 振蕩器類型:內部 工作溫度:* 封裝/外殼:- 供應商器件封裝:- 標準包裝:1 |
| ADUC814ARU | 功能描述:IC ADC 12BIT W/FLASH MCU 28TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。