- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C554B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C554B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大），16字節的FIFO |
| 文件頁數： | 30/51頁 |
| 文件大?。?/td> | 253K |
| 代理商： | SC16C554B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
9397 750 13133
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 9 February 2005
30 of 51
Philips Semiconductors
SC16C554B/554DB
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 19:
Bit
7:6
5
4
Modem Control Register bits description
Symbol
Description
MCR[7:6]
Reserved; set to ‘0’.
MCR[5]
Autoflow control enable.
MCR[4]
Loop-back. Enable the local loop-back mode (diagnostics). In this mode
the transmitter output (TX) and the receiver input (RX), CTS, DSR, CD,
and RI are disconnected from the SC16C554B/554DB I/O pins. Internally
the modem data and control pins are connected into a loop-back data
configuration (see
Figure 12
). In this mode, the receiver and transmitter
interrupts remain fully operational. The Modem Control Interrupts are
also operational, but the interrupts’ sources are switched to the lower four
bits of the Modem Control. Interrupts continue to be controlled by the IER
register.
Logic 0 = Disable loop-back mode (normal default condition).
Logic 1 = Enable local loop-back mode (diagnostics).
MCR[3]
OP2, INTx enable. Used to control the modem CD signal in the loop-back
mode.
Logic 0 = Forces INTA to INTD outputs to the 3-state mode during the
16 mode (normal default condition). In the loop-back mode, sets OP2
(CD) internally to a logic 1.
Logic 1 = Forces the INTA to INTD outputs to the active mode during
the 16 mode. In the loop-back mode, sets OP2 (CD) internally to a
logic 0.
MCR[2]
OP1. This bit is used in the Loop-back mode only. In the loop-back mode,
this bit is used to write the state of the modem RI interface signal via
OP1.
MCR[1]
RTS
Logic 0 = Force RTS output to a logic 1 (normal default condition).
Logic 1 = Force RTS output to a logic 0.
Automatic RTS may be used for hardware flow control by enabling
MCR[5].
MCR[0]
DTR
Logic 0 = Force DTR output to a logic 1 (normal default condition).
Logic 1 = Force DTR output to a logic 0.
3
2
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754B | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554B_10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| SC16C554BIB64 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 PBF | 制造商:NXP Semiconductors 功能描述: |
| SC16C554BIB64,151 | 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。