- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C554B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C554B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大），16字節的FIFO |
| 文件頁數： | 24/51頁 |
| 文件大?。?/td> | 253K |
| 代理商： | SC16C554B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
9397 750 13133
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 9 February 2005
24 of 51
Philips Semiconductors
SC16C554B/554DB
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
7.1 Transmit (THR) and Receive (RHR) Holding Registers
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7 to D0) to the
THR, providing that the THR or TSR is empty. The THR empty flag in the LSR register will
be set to a logic 1 when the transmitter is empty or when data is transferred to the TSR.
Note that a write operation can be performed when the THR empty flag is set
(logic 0 = FIFO full; logic 1 = at least one FIFO location available).
The serial receive section also contains an 8-bit Receive Holding Register (RHR).
Receive data is removed from the SC16C554B/554DB and receive FIFO by reading the
RHR register. The receive section provides a mechanism to prevent false starts. On the
falling edge of a start or false start bit, an internal receiver counter starts counting clocks
at the 16
×
clock rate. After 7
1
2
clocks, the start bit time should be shifted to the center of
the start bit. At this time the start bit is sampled, and if it is still a logic 0 it is validated.
Evaluating the start bit in this manner prevents the receiver from assembling a false
character. Receiver status codes will be posted in the LSR.
7.2 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receiver ready, transmitter
empty, line status and modem status registers. These interrupts would normally be seen
on the INTA to INTD output pins in the 16 mode, or on wire-OR IRQ output pin in the
68 mode.
Table 10:
Bit
7:4
3
Interrupt Enable Register bits description
Symbol
Description
IER[7:4]
Reserved; set to ‘0’.
IER[3]
Modem Status Interrupt.
Logic 0 = Disable the modem status register interrupt (normal default
condition).
Logic 1 = Enable the modem status register interrupt.
IER[2]
Receive Line Status interrupt.
Logic 0 = Disable the receiver line status interrupt (normal default condition).
Logic 1 = Enable the receiver line status interrupt.
IER[1]
Transmit Holding Register interrupt. This interrupt will be issued whenever the
THR is empty, and is associated with LSR[1].
Logic 0 = Disable the transmitter empty interrupt (normal default condition).
Logic 1 = Enable the transmitter empty interrupt.
IER[0]
Receive Holding Register interrupt. This interrupt will be issued when the FIFO
has reached the programmed trigger level, or is cleared when the FIFO drops
below the trigger level in the FIFO mode of operation.
Logic 0 = Disable the receiver ready interrupt (normal default condition).
Logic 1 = Enable the receiver ready interrupt.
2
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754B | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554B_10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| SC16C554BIB64 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 PBF | 制造商:NXP Semiconductors 功能描述: |
| SC16C554BIB64,151 | 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。