- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C554B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C554B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大），16字節的FIFO |
| 文件頁數： | 16/51頁 |
| 文件大小： | 253K |
| 代理商： | SC16C554B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
9397 750 13133
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 9 February 2005
16 of 51
Philips Semiconductors
SC16C554B/554DB
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
6.4 Autoflow control (see
Figure 7
)
Autoflow control is comprised of auto-CTS and auto-RTS. With auto-CTS, the CTS input
must be active before the transmitter FIFO can emit data. With auto-RTS, RTS becomes
active when the receiver needs more data and notifies the sending serial device. When
RTS is connected to CTS, data transmission does not occur unless the receiver FIFO has
space for the data; thus, overrun errors are eliminated using UART 1 and UART 2 from a
SC16C554B/554DB with the autoflow control enabled. If not, overrun errors occur when
the transmit data rate exceeds the receiver FIFO read latency.
6.4.1
Auto-RTS (see
Figure 7
)
Auto-RTS data flow control originates in the receiver timing and control block (see block
diagrams in
Figure 1
and
Figure 2
) and is linked to the programmed receiver FIFO trigger
level. When the receiver FIFO level reaches a trigger level of 1, 4, or 8 (see
Figure 9
), RTS
is de-asserted. With trigger levels of 1, 4, and 8, the sending UART may send an
additional byte after the trigger level is reached (assuming the sending UART has another
byte to send) because it may not recognize the de-assertion of RTS until after it has
begun sending the additional byte. RTS is automatically reasserted once the RX FIFO is
emptied by reading the receiver buffer register. When the trigger level is 14 (see
Figure 10
), RTS is de-asserted after the first data bit of the 16th character is present on
the RX line. RTS is reasserted when the RX FIFO has at least one available byte space.
6.4.2
Auto-CTS (see
Figure 7
)
The transmitter circuitry checks CTS before sending the next data byte. When CTS is
active, it sends the next byte. To stop the transmitter from sending the following byte, CTS
must be released before the middle of the last stop bit that is currently being sent (see
Figure 8
). The auto-CTS function reduces interrupts to the host system. When flow control
is enabled, CTS level changes do not trigger host interrupts because the device
automatically controls its own transmitter. Without auto-CTS, the transmitter sends any
data present in the transmit FIFO and a receiver overrun error may result.
Fig 7.
Autoflow control (auto-RTS and auto-CTS) example
RCV
FIFO
SERIAL TO
PARALLEL
FLOW
CONTROL
XMT
FIFO
PARALLEL
TO SERIAL
FLOW
CONTROL
PARALLEL
TO SERIAL
FLOW
CONTROL
SERIAL TO
PARALLEL
FLOW
CONTROL
XMT
FIFO
RCV
FIFO
ACE1
ACE2
D7 to D0
RX
TX
RTS
CTS
TX
RX
D7 to D0
002aaa048
CTS
RTS
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754B | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554B_10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| SC16C554BIB64 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 PBF | 制造商:NXP Semiconductors 功能描述: |
| SC16C554BIB64,151 | 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。