- 您現在的位置：買賣IC網 > PDF目錄383804 > SC16C554B (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C554B |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大），16字節的FIFO |
| 文件頁數： | 11/51頁 |
| 文件大?。?/td> | 253K |
| 代理商： | SC16C554B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
9397 750 13133
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 9 February 2005
11 of 51
Philips Semiconductors
SC16C554B/554DB
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
IOW
18
9
31
I
Input/Output Write strobe (active LOW).
This function is
associated with the 16 mode only. A logic 0 transition on this pin will
transfer the contents of the data bus (D0 to D7) from the external
CPU to an internal register that is defined by address bits A0 to A2.
When the 68 mode is selected, this pin functions as R/W (see
definition under R/W).
Interrupt Request or Interrupt ‘A’.
This function is associated with
the 68 mode only. In the 68 mode, interrupts from UART channels
A to D are wire-ORed internally to function as a single IRQ
interrupt. This pin transitions to a logic 0 (if enabled by the interrupt
enable register) whenever a UART channel(s) requires service.
Individual channel interrupt status can be determined by addressing
each channel through its associated internal register, using CS and
A3 to A4. In the 68 mode, and external pull-up resistor must be
connected between this pin and V
CC
. The function of this pin
changes to INTA when operating in the 16 mode (see definition
under INTA).
not connected
IRQ
15
-
-
O
n.c.
21, 49,
52, 54,
55, 65
-
1, 10,
20, 21,
30, 40,
41, 49,
52, 60,
61, 71,
80
53
-
RESET
(RESET)
37
27
I
Reset.
In the 16 mode, a logic 1 on this pin will reset the internal
registers and all the outputs. The UART transmitter output and the
receiver input will be disabled during reset time. (See
Section 7.10
“SC16C554B/554DB external reset conditions”
for initialization
details.) When 16/68 is a logic 0 (68 mode), this pin functions
similarly, bus as an inverted reset interface signal, RESET.
Ring Indicator (active LOW).
These inputs are associated with
individual UART channels, A to D. A logic 0 on this pin indicates the
modem has received a ringing signal from the telephone line. A
logic 1 transition on this input pin will generate an interrupt.
Request to Send (active LOW).
These outputs are associated with
individual UART channels, A to D. A logic 0 on the RTS pin
indicates the transmitter has data ready and waiting to send. Writing
a logic 1 in the modem control register MCR[1] will set this pin to a
logic 0, indicating data is available. After a reset this pin will be set
to a logic 1. This pin only affects the transmit and receive operations
when auto-RTS function is enabled via MCR[5] for hardware flow
control operation.
Read/Write strobe.
This function is associated with the 68 mode
only. This pin provides the combined functions for Read or Write
strobes.
Logic 1 = Read from UART register selected by CS and A0 to A4.
Logic 0 = Write to UART register selected by CS and A0 to A4.
RIA, RIB,
RIC, RID
8, 28,
42, 62
63, 19,
30, 50
18, 43,
58, 3
I
RTSA,RTSB,
RTSC, RTSD
14, 22,
48, 56
5, 13,
36, 44
26, 35,
66, 75
O
R/W
18
-
-
I
Table 2:
Pin description
…continued
Pin
PLCC68
Symbol
Type
Description
LQFP64
LQFP80
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754B | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC68C752B | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface |
| SCAN182245AMTD | Non-Inverting Transceiver with 25ohm Series Resistor Outputs |
| SCAN18245TSSC | Non-Inverting Transceiver with 3-STATE Outputs |
| SCAN18374T | D-Type Flip-Flop with 3-STATE Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554B_10 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| SC16C554BIB64 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554BIB64,128 PBF | 制造商:NXP Semiconductors 功能描述: |
| SC16C554BIB64,151 | 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。