參數資料
型號： S1C63567F0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP144
封裝： PLASTIC, QFP-144
文件頁數： 55/172頁
文件大?。?/td> 1349K
代理商： S1C63567F0A0100
138
EPSON
S1C63567 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Interrupt and HALT)
Table 4.15.4.1(b) Control bits of interrupt (2)
Address
Comment
D3
D2
Register
D1
D0
Name
Init 1
10
FFF6H
IT3
IT2
IT1
IT0
R/W
IT3
IT2
IT1
IT0
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Interrupt factor flag (Clock timer 1 Hz)
Interrupt factor flag (Clock timer 2 Hz)
Interrupt factor flag (Clock timer 8 Hz)
Interrupt factor flag (Clock timer 32 Hz)
FFF5H
000
IK1
R
R/W
0 3
IK1
– 2
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Unused
Interrupt factor flag (K10–K13)
FFF7H
00
ISW1
ISW10
R
R/W
0 3
ISW1
ISW10
– 2
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Unused
Interrupt factor flag (Stopwatch timer 1 Hz)
Interrupt factor flag (Stopwatch timer 10 Hz)
FFF9H
000
ID
R
R/W
0 3
ID
– 2
0
(R)
Yes
(W)
Reset
(R)
No
(W)
Invalid
Unused
Interrupt factor flag (Dialer)
*1 Initial value at initial reset
*3 Constantly "0" when being read
*2 Not set in the circuit
EID: Interrupt mask register (FFE9HD0)
ID: Interrupt factor flag (FFF9HD0)
Refer to Section 4.14, "Telephone Function".
EIPT1, EIPT0: Interrupt mask registers (FFE2HD1, D0)
IPT1, IPT0: Interrupt factor flags (FFF2HD1, D0)
Refer to Section 4.10, "Programmable Timer".
EISER, EISTR, EISRC: Interrupt mask registers (FFE3HD2–D0)
ISER, ISTR, ISRC: Interrupt factor flags (FFF3HD2–D0)
Refer to Section 4.11, "Serial Interface".
KCP03–KCP00, KCP13–KCP10: Input comparison registers (FF22H, FF26H)
SIK03–SIK00, SIK13–SIK10: Interrupt selection registers (FF20H, FF24H)
EIK0, EIK1: Interrupt mask registers (FFE4HD0, FFE5HD0)
IK0, IK1: Interrupt factor flags (FFF4HD0, FFF5HD0)
Refer to Section 4.4, "Input Ports".
EIT3–EIT0: Interrupt mask registers (FFE6H)
IT3–IT0: Interrupt factor flags (FFF6H)
Refer to Section 4.8, "Clock Timer".
EISW1, EISW10: Interrupt mask registers (FFE7HD1, D0)
ISW1, ISW10: Interrupt factor flags (FFF7HD1, D0)
Refer to Section 4.9, "Stopwatch Timer".
4.15.5 Programming notes
(1) The interrupt factor flags are set when the interrupt condition is established, even if the interrupt
mask registers are set to "0".
(2) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
(3) After an initial reset, all the interrupts including NMI are masked until both the stack pointers SP1
and SP2 are set with the software. Be sure to set the SP1 and SP2 in the initialize routine. Further,
when re-setting the stack pointer, the SP1 and SP2 must be set as a pair. When one of them is set, all
the interrupts including NMI are masked and interrupts cannot be accepted until the other one is set.
相關PDF資料
PDF描述
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
S1C6F567D0A0100 MICROCONTROLLER, UUC141
S1C6N3B0D0A0100 MICROCONTROLLER, UUC54
S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102
S1C6P466D0A0A00 MICROCONTROLLER, UUC140
相關代理商/技術參數
參數描述
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
S1C63656 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63657 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*