參數資料
型號： S1C63567F0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP144
封裝： PLASTIC, QFP-144
文件頁數： 135/172頁
文件大?。?/td> 1349K
代理商： S1C63567F0A0100
S1C63567 TECHNICAL MANUAL
EPSON
55
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Clock Timer)
4.8 Clock Timer
4.8.1 Configuration of clock timer
The S1C63567 has a built-in clock timer that uses OSC1 (crystal oscillator) as the source oscillator. The
clock timer is configured of an 8-bit binary counter that serves as the input clock, fOSC1 divided clock
output from the prescaler. Timer data (128–16 Hz and 8–1 Hz) can be read out by the software.
Figure 4.8.1.1 is the block diagram for the clock timer.
128 Hz–16 Hz
Data bus
32 Hz, 8 Hz, 2 Hz, 1 Hz
256 Hz
Clock timer reset signal
Divider
Interrupt
request
Interrupt
control
8 Hz–1 Hz
Clock timer RUN/STOP signal
Clock timer
OSC1
oscillation circuit
(fOSC1)
Fig. 4.8.1.1 Block diagram for the clock timer
Ordinarily, this clock timer is used for all types of timing functions such as clocks.
Note: When the CR oscillation circuit is selected as the OSC1 oscillation circuit by mask option, the
frequencies and times differ from the values described in this section because the oscillation
frequency will be 60 kHz (Typ.). Therefore, the clock timer can not be used for the clock function.
4.8.2 Data reading and hold function
The 8 bits timer data are allocated to the address FF79H and FF7AH.
<FF79H>
D0: TM0 = 128 Hz
D1: TM1 = 64 Hz
D2: TM2 = 32 Hz
D3: TM3 = 16 Hz
<FF7AH>
D0: TM4 = 8 Hz
D1: TM5 = 4 Hz
D2: TM6 = 2 Hz
D3: TM7 = 1 Hz
Since the clock timer data has been allocated to two addresses, a carry is generated from the low-order
data within the count (TM0–TM3: 128–16 Hz) to the high-order data (TM4–TM7: 8–1 Hz). When this carry
is generated between the reading of the low-order data and the high-order data, a content combining the
two does not become the correct value (the low-order data is read as FFH and the high-order data
becomes the value that is counted up 1 from that point).
The high-order data hold function in the S1C63567 is designed to operate to avoid this. This function
temporarily stops the counting up of the high-order data (by carry from the low-order data) at the point
where the low-order data has been read and consequently the time during which the high-order data is
held is the shorter of the two indicated here following.
1. Period until it reads the high-order data.
2. 0.48–1.5 msec (Varies due to the read timing.)
Note: Since the low-order data is not held when the high-order data has previously been read, the low-
order data should be read first.
相關PDF資料
PDF描述
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
S1C6F567D0A0100 MICROCONTROLLER, UUC141
S1C6N3B0D0A0100 MICROCONTROLLER, UUC54
S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102
S1C6P466D0A0A00 MICROCONTROLLER, UUC140
相關代理商/技術參數
參數描述
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
S1C63656 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63657 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*