參數資料
型號： S1C63567F0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP144
封裝： PLASTIC, QFP-144
文件頁數： 49/172頁
文件大?。?/td> 1349K
代理商： S1C63567F0A0100
132
EPSON
S1C63567 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Telephone Function)
EID: Interrupt mask register (FFE9HD0)
Enables or disables the generation of an interrupt for the CPU.
When "1" is written: Enabled
When "0" is written: Disabled
Reading: Valid
EID is the interrupt mask register corresponding to the dialing interrupt factor. Interrupts set to "1" are
enabled and interrupts set to "0" are disabled.
At initial reset, this register is set to "0".
ID: Interrupt factor flag (FFF9HD0)
Indicates the dialing interrupt generation status.
When "1" is read: Interrupt has occurred
When "0" is read: Interrupt has not occurred
When "1" is written: Flag is reset
When "0" is written: Invalid
The interrupt factor flag ID is set to "1" when a dialing interrupt factor occurs (when a dialing output, pause
or flash cycle is completed). After executing a dialing function (dialing number, pause, flash), this flag
must be reset. Otherwise, the next dialing function can not be executed.
The interrupt factor flag is reset to "0" by writing "1".
After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1") is
set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to reset
(write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt
enabled state.
At initial reset, this flag is set to "0".
4.14.11 Programming notes
(1) It is necessary to turn the OSC3 oscillation on prior to a dialing operation in tone mode because the
tone mode uses the OSC3 (3.58 MHz) clock. However it increases current consumption. Therefore,
turn the OSC3 oscillation off after finishing the dialling operation in tone mode.
(2) Do not write "0" (0000B) to the IDP, FTS, PTS or TCD (in pulse mode) registers because it may cause a
malfunction.
(3) The pause function control bit PAUSE (FF14HD1) and the flash function control bit FLASH
(FF14HD0) are write-only, so software cannot control these functions (on address FF14H) using an
ALU instruction (AND, OR ...). Furthermore, be aware that the pause function or the flash function is
canceled when "0" is written to the PAUSE bit (FF14HD1) or the FLASH bit (FF14HD0).
(4) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
相關PDF資料
PDF描述
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
S1C6F567D0A0100 MICROCONTROLLER, UUC141
S1C6N3B0D0A0100 MICROCONTROLLER, UUC54
S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102
S1C6P466D0A0A00 MICROCONTROLLER, UUC140
相關代理商/技術參數
參數描述
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
S1C63656 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63657 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*