- 您現在的位置：買賣IC網 > PDF目錄383723 > OR3TP12-6PS240 Single 2.3V 10 MHZ OP, -40C to +125C, 14-SOIC 150mil, T/R PDF資料下載
參數資料
| 型號： | OR3TP12-6PS240 |
| 英文描述： | Single 2.3V 10 MHZ OP, -40C to +125C, 14-SOIC 150mil, T/R |
| 中文描述： | 用戶可編程ASIC的特殊功能 |
| 文件頁數： | 102/128頁 |
| 文件大小： | 2450K |
| 代理商： | OR3TP12-6PS240 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁當前第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
ORCAOR3TP12 FPSC
Embedded Master/Target PCI Interface
Data Sheet
March 2000
102
L Lucent Technologies Inc.
Symbol
I/O
Description
Dedicated Pins
V
DD
GND
RESET
—
—
I
Positive power supply.
Ground supply.
During configuration, RESET forces the restart of configuration and a pull-up is
enabled. After configuration, RESET can be used as an FPGA logic direct input,
which causes all PLC latches/FFs to be asynchronously set/reset.
In the Master and asynchronous peripheral modes, CCLK is an output which strobes
configuration data in. In the slave or synchronous peripheral mode, CCLK
is input synchronous with the data on DIN or D[7:0]. In microprocessor and PCI
modes, CCLK is used internally and output for daisy-chain operation.
As an input, a low level on DONE delays FPGA start-up after configuration.*
As an active-high, open-drain output, a high level on this signal indicates that config-
uration is complete. DONE is also used in the embedded PCI core start-up
sequence. DONE has an optional pull-up resistor.
PRGM is an active-low input that forces the restart of configuration and resets the
boundary-scan circuitry. This pin always has an active pull-up.
This pin must be held high during device initialization until the INIT pin goes high.
This pin always has an active pull-up.
During configuration, RD_CFG is an active-low input that activates the TS_ALL
function and 3-states all of the I/O.
After configuration, RD_CFG can be selected (via a bit stream option) to activate the
TS_ALL function as described above, or, if readback is enabled via a bit stream
option, a high-to-low transition on RD_CFG will initiate readback of the configuration
data, including PFU output states, starting with frame address 0.
RD_DATA/TDO is a dual-function pin. If used for readback, RD_DATA provides con-
figuration data out. If used in boundary scan, TDO is test data out.
CCLK
I
DONE
I
O
PRGM
I
RD_CFG
I
RD_DATA/TDO
O
Special-Purpose Pins
M0, M1, M2
I
I/O
I
During powerup and initialization, M0—M2 are used to select the configuration
mode with their values latched on the rising edge of INIT; see Table 28 for the con-
figuration modes. During configuration, a pull-up is enabled.
After configuration, M2 can be a user-programmable I/O.*
During powerup and initialization, M3 is used to select the speed of the internal
oscillator during configuration with their values latched on the rising edge of INIT.
When M3 is low, the oscillator frequency is 10 MHz. When M3 is high, the oscillator
is 1.25 MHz. During configuration, a pull-up is enabled.
After configuration, M2 can be a user-programmable I/O pin.*
M3
I/O
* The ORCASeries 3 FPGA data sheet contains more information on how to control these signals during start-up. The timing of DONE release
is controlled by one set of bit stream options, and the timing of the simultaneous release of all other configuration pins (and the activation of all
user I/Os) is controlled by a second set of options.
Pin Information
This section describes the pins and signals that perform FPGA-related functions. Any pins not described in Table 5
or here in Table 41 are user-programmable I/Os. During configuration, the user-programmable I/Os are 3-stated
and pulled-up with an internal resistor. If any FPGA function pin is not used (or not bonded to package pin), it is
also 3-stated and pulled-up after configuration.
Table 41. FPGA Common-Function Pin Descriptions
相關PDF資料 |
PDF描述 |
|---|---|
| OR3TP12-6PS240I | Quad 2.3V 10 MHz OP, I temp, -40C to +85C, 14-SOIC 150mil, T/R |
| OR3TP12 | Field-Programmable System Chip (FPSC) Embedded Master/Target PCI Interface |
| OR62 | OR62 is a 6-input OR gate with 2x drive strength |
| OR73 | 7-input OR gate with 3x drive strength. |
| OR8GU41 | DIFFUSED TYPE (HIGH SPEED RECTIFIER APPLICATIONS) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3TP12-6PS240I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:User Programmable Special Function ASIC |
| OR3TP127BA256-DB | 功能描述:FPGA - 現場可編程門陣列 2016 LUT 187 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256 |
| OR3TP127BA352-DB | 功能描述:FPGA - 現場可編程門陣列 2016 LUT 187 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256 |
| OR4 | 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:ORCASeries 4 FPGAs |
| OR-401045290 | 制造商:ORTRONICS 功能描述:ORTRONICS 24 PORT MODULAR PATCH PANEL |
發布緊急采購，3分鐘左右您將得到回復。