- 您現在的位置：買賣IC網 > PDF目錄383723 > OR3TP12-6BA256I Single 2.3V 10 MHZ OP, -40C to +125C, 14-SOIC 150mil, TUBE PDF資料下載
參數資料
| 型號： | OR3TP12-6BA256I |
| 英文描述： | Single 2.3V 10 MHZ OP, -40C to +125C, 14-SOIC 150mil, TUBE |
| 中文描述： | 用戶可編程ASIC的特殊功能 |
| 文件頁數： | 103/128頁 |
| 文件大小： | 2450K |
| 代理商： | OR3TP12-6BA256I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁當前第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
Lucent Technologies Inc.
Lucent Technologies Inc.
103
Data Sheet
March 2000
ORCA OR3TP12 FPSC
Embedded Master/Target PCI Interface
Table 41. FPGA Common-Function Pin Descriptions
(continued)
** The ORCA Series 3 FPGA data sheet contains more information on how to control these signals during start-up. The timing of DONE release
is controlled by one set of bit stream options, and the timing of the simultaneous release of all other configuration pins (and the activation of all
user I/Os) is controlled by a second set of options.
Symbol
I/O
Description
Special-Purpose Pins
(continued)
TDI, TCK, TMS
I
I/O
O
If boundary scan is used, these pins are test data in, test clock, and test mode select
inputs. If boundary scan is not selected, all boundary-scan functions are inhibited
once configuration is complete. Even if boundary scan is not used, either TCK or
TMS must be held at logic one during configuration. Each pin has a pull-up enabled
during configuration.
After configuration, these pins are user-programmable I/O.*
During configuration in peripheral mode, RDY/RCLK indicates another byte can be
written to the FPGA. If a read operation is done when the device is selected, the
same status is also available on D7 in asynchronous peripheral mode.
During the Master parallel configuration mode, RCLK is a read output signal to an
external memory. This output is not normally used.
In i960microprocessor mode, this pin acts as the address latch enable (ALE) input.
After configuration, if the MPI is not used, this pin is a user-programmable I/O pin.*
High during configuration is output high until configuration is complete. It is used as
a control output indicating that configuration is not complete.
Low during configuration is output low until configuration is complete. It is used as a
control output indicating that configuration is not complete.
INIT is a bidirectional signal before and during configuration. During configuration, a
pull-up is enabled, but an external pull-up resistor is recommended. As an active-low
open-drain output, INIT is held low during power stabilization and internal clearing of
memory. As an active-low input, INIT holds the FPGA in the wait-state before the
start of configuration.
CS0 and CS1 are used in the asynchronous peripheral, slave parallel, and micropro-
cessor configuration modes. The FPGA is selected when CS0 is low and CS1 is
high. During configuration, a pull-up is enabled.
RDY/RCLK/
MPI_ALE
O
I
I/O
O
HDC
LDC
O
INIT
I/O
CS0, CS1
I
I/O
I
After configuration, these pins are user-programmable I/O pins.*
RD is used in the asynchronous peripheral configuration mode. A low on RD
changes D7 into a status output. As a status indication, a high indicates ready, and a
low indicates busy. WR and RD should not be used simultaneously. If they are, the
write strobe overrides.
This pin is also used as the microprocessor interface (MPI) data transfer strobe. For
PowerPC it is the transfer start (TS). For i960, it is the address/data strobe (
ads
).
After configuration, if the MPI is not used, this pin is a user-programmable I/O pin.*
WR is used in the asynchronous peripheral configuration mode. When the FPGA is
selected, a low on the write strobe, WR, loads the data on D[7:0] inputs into an
internal data buffer. WR and RD should not be used simultaneously. If they are, the
write strobe overrides.
After configuration, this pin is a user-programmable I/O pin.*
RD/MPI_STRB
I
I/O
I
WR
I/O
Pin Information
(continued)
相關PDF資料 |
PDF描述 |
|---|---|
| OR3TP12-6BA352 | Quad 2.3V 10 MHz OP, I temp, -40C to +85C, 14-PDIP, TUBE |
| OR3TP12-6BA352I | Quad 2.3V 10 MHz OP, I temp, -40C to +85C, 14-TSSOP, TUBE |
| OR3TP12-6PS240 | Single 2.3V 10 MHZ OP, -40C to +125C, 14-SOIC 150mil, T/R |
| OR3TP12-6PS240I | Quad 2.3V 10 MHz OP, I temp, -40C to +85C, 14-SOIC 150mil, T/R |
| OR3TP12 | Field-Programmable System Chip (FPSC) Embedded Master/Target PCI Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3TP126BA256I-DB | 功能描述:FPGA - 現場可編程門陣列 2016 LUT 187 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256 |
| OR3TP12-6BA352 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:User Programmable Special Function ASIC |
| OR3TP126BA352-DB | 功能描述:FPGA - 現場可編程門陣列 2016 LUT 187 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256 |
| OR3TP12-6BA352I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:User Programmable Special Function ASIC |
| OR3TP126BAN256-DB | 制造商:Lattice Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。