- 您現在的位置：買賣IC網 > PDF目錄358722 > L29S800F (Electronic Theatre Controls, Inc.) 8MEGABIT (1M】8 /512K】16) 3 VOLT CMOS FLASH MEMERY PDF資料下載
參數資料
| 型號： | L29S800F |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 8MEGABIT (1M】8 /512K】16) 3 VOLT CMOS FLASH MEMERY |
| 中文描述： | 8MEGABIT（100萬】8 / 16】為512k）3伏的CMOS閃存MEMERY |
| 文件頁數： | 20/54頁 |
| 文件大?。?/td> | 797K |
| 代理商： | L29S800F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
L29S800F
PRELIMINARY
A
8MEGABIT (1M×8 /512K×16)
3 VOLT CMOS FLASH MEMERY
LinkSmart
20
071802
Extended Command
(1) Fast Mode
L29S800F/-B has Fast Mode function. This mode dispenses with the initial two unclock cycles
required in the standard program command sequence by writing Fast Mode command into the
command register. In this mode, the required bus cycle for programming is two cycles instead of
four bus cycles in standard program command. (Do not write erase command in this mode.) The
read operation is also executed after exiting this mode. To exit this mode, it is necessary to write
Fast Mode Reset command into the command register. (Refer to the Figure 27 Extended
algorithm.) The V
CC
active current is required even
CE
= V
IH
during Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The
Embedded Program Algorithm is executed by writing program set-up command (A0H) and data
write cycles (PA/PD). (Refer to the Figure 27 Extended algorithm.)
(3) Extended Sector Protection
In addition to normal sector protection, the L29S800F/-B has Extended Sector Protection as
extended function. This function enable to protect sector by forcing V
ID
on
RESET
pin and write a
command sequence. Unlike conventional procedure, it is not necessary to force V
ID
and control
timing for control pins. The only
RESET
pin requires V
ID
for sector protection in this mode. The
extended sector protect requires V
ID
on
RESET
pin. With this condition, the operation is initiated
by writing the set-up command (60H) into the command register. Then, the sector addresses pins
(A
18
, A
17
, A
16
, A
15
, A
14
, A
13
and A
12
) and (A
6
, A
1
, A
0
) = (0, 1, 0) should be set to the sector to be
protected (recommend to set V
IL
for the other addresses pins), and write extended sector protect
command (60H). A sector is typically protected in 150 ms. To verify programming of the protection
circuitry, the sector addresses pins (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
and A
12
) and (A
6
, A
1
, A
0
) = (0, 1, 0)
should be set and write a command (40H). Following the command write, a logical “1” at device
output DQ
0
will produce for protected sector in the read operation. If the output data is logical “0”,
please repeat to write extended sector protect command (60H) again. To terminate the operation, it
is necessary to set
RESET
pin to V
IH
.
相關PDF資料 |
PDF描述 |
|---|---|
| L317LC | 3-TERMINAL ADJUSTABLE REGULATOR |
| l321 | CAP CER 1.5UF 50V 10% X7R 1812 |
| l345 | Thyristor Module |
| L349 | Three Phase Rectifier Bridge |
| L34F3BT | T-1 INFRA-RED EMITTING DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L2A050-01 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Two-Wire Serial Backplane Controller |
| L2A0525 | 制造商:LSI Corporation 功能描述:2A0525 |
| L2A0572 | 制造商:LSI 功能描述: 制造商:LSI Corporation 功能描述: |
| L2A1393 WAF | 制造商:Rochester Electronics LLC 功能描述: |
| L2A1439 | 制造商:Vitesse Semiconductor Corporation 功能描述:2A1439 |
發布緊急采購，3分鐘左右您將得到回復。