參數資料
型號： KSZ8862-16MQL-FX
廠商： Micrel Inc
文件頁數： 67/125頁
文件大?。?/td> 0K
描述： IC SWITCH ETH 2P 16BIT 128PQFP
標準包裝： 66
系列： KSZ8862
控制器類型： 以太網開關控制器
接口： PCI
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1638-ND - BOARD EVALUATION KSZ8862-10FL
576-1637-ND - BOARD EVALUATION KSZ8862-100FX
其它名稱： 576-3271
Micrel, Inc.
KSZ8862-16/32MQL
April 2007
46
M9999-040407-3.0
The format for ConfigParam is shown in Table 13.
Bit
Bit Name
Description
15 -2
Reserved
1
Clock_Rate
Internal clock rate selection
0: 125 MHz
1: 25 MHz
Note: At power up, this chip operates on 125 MHz clock. The internal frequency can be
dropped to 25 MHz via the external EEPROM.
0
ASYN_8bit
Async 8-bit or 16-bit bus select
1= bus is configured for 16-bit width
0= bus is configured for 8-bit width
(32-bit width, KSZ8862-32, don’t care this bit setting)
Table 13. ConfigParam Word in EEPROM Format
Loopback Support
The KSZ8862M provides loopback support for remote diagnostic of failure. In loopback mode, the speed at both PHY
ports will be set to 100BASE-TX full-duplex mode. Two types of loopback are supported: Far-end Loopback and Near-end
(Remote) Loopback.
Far-end Loopback
Far-end loopback is conducted between the KSZ8862M’s two PHY ports. The loopback path starts at the “Originating.”
PHY port’s receive inputs (RXP/RXM), wraps around at the “l(fā)oopback” PHY port’s PMD/PMA, and ends at the
“Originating” PHY port’s transmit outputs (TXP/TXM).
Bit [8] of registers P1CR4 and P2CR4 is used to enable far-end loopback for ports 1 and 2, respectively. Alternatively, Bit
[14] of registers P1MBCR and P2MBCR can also be used to enable far-end loopback. The port 2 far-end loopback path is
illustrated in the Figure 12.
Near-end (Remote) Loopback
Near-end (Remote) loopback is conducted at either PHY port 1 or PHY port 2 of the KSZ8862M. The loopback path starts
at the PHY port receiving inputs (RXPx/RXMx), wraps around at the same PHY port’s PMD/PMA, and ends at the PHY
port’s transmit outputs (TXPx/TXMx).
Bit [1] of registers P1PHYCTRL and P2PHYCTRL is used to enable near-end loopback for ports 1 and 2, respectively.
Alternatively, Bit [9] of registers P1SCSLMD and P2SCSLMD can also be used to enable near-end loopback. The both
ports 1 and 2 near-end loopback paths are illustrated in the following Figure 13.
相關PDF資料
PDF描述
PIC16LF726-E/SO IC PIC MCU FLASH 8KX14 28-SOIC
0731010340 BNC JACK VERTICAL PCB 75 OHM
V300A5C400BF CONVERTER MOD DC/DC 5V 400W
V300A5C400BL3 CONVERTER MOD DC/DC 5V 400W
PIC16LC620A-04/SS IC MCU OTP 512X14 COMP 20SSOP
相關代理商/技術參數
參數描述
KSZ8862-32MQL 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-32MQL-FX 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (32-bit) bus interface. Fiber Capabilities on Port-1(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8862-MQL 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface and Fiber Support
KSZ8863FLL 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863FLL-EVAL 功能描述:以太網開發工具 3-Port 10/100 Ethernet Switch with 1x FX Port and 1x TX Port - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*